22 open source boards using the LM317T

Real designs built with the LM317T, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

22 boardsClear filters|Most starred

How designs wire the LM317T

Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the LM317T connects to, and the resistors, capacitors and other passives placed on it.

  • The ADJ pin has a series resistor on 11 of 18 designs, most often 240 Ω (then 200 Ω).
  • The VO_2 pin has a capacitor to GND on 9 of 18 designs, most often 100 nF (then 10 µF).
  • The VO_2 pin has a series resistor on 8 of 18 designs, most often 10 kΩ (then 240 Ω).
ADJpin 1Connected to: Signal 89%
  • Series resistor on 61% · 240 Ω (2), 200 Ω (1), 392 Ω (1)
  • Resistor to GND on 39% · 1 kΩ (1), 2.74 kΩ (1), 4.7 kΩ (1)
VO_2pin 2Connected to: A connector 22% · 1.35V 33%
  • Capacitor to GND on 50% · 100 nF (5), 10 µF (3), 100 µF (2)
  • Series resistor on 44% · 10 kΩ (3), 240 Ω (2), 1 Ω (2)
VI_3pin 3Connected to: VCC 56% · a signal 44%
  • Decoupling capacitor on 33% · 100 nF (5), 10 µF (1), 1 mF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Adjustable Modular Power Supply by thebiguno, BenchBudEE by ContextualElectronics, Rti by cceh and 6ch af preamplifier by dilshan.

The LM317T in open source designs

The gallery holds 22 open source boards using the LM317T from 18 GitHub repositories; a typical one measures about 99.8 × 68 mm and carries around 58 components.

91% are two-layer designs, the rest use four layers or more, and 32% carry an open source license.

The most starred is Power Supply (plus UBBB 32u4 rev 1.2) by thebiguno.

Parts used alongside the LM317T

Microcontrollers on boards using the LM317T

LM317T: common questions

Where can I find a LM317T reference design?

Each of the 22 boards on this page is a real design using the LM317T. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LM317T ADJ pin?

The ADJ pin has a series resistor on 11 of 18 designs, most often 240 Ω (then 200 Ω). Counted from the KiCad layouts of 18 open source designs using the LM317T.

How is the LM317T VO_2 pin connected?

The VO_2 pin has a capacitor to GND on 9 of 18 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 18 open source designs using the LM317T.

Which microcontrollers do boards using the LM317T use?

Most are built on AVR/Arduino (7), NXP (1) and PIC (1).

How big is a typical board using the LM317T?

The median is 99.8 × 68 mm, and 91% are two-layer designs.

What is the most popular open source board using the LM317T?

By GitHub stars, Power Supply (plus UBBB 32u4 rev 1.2) by thebiguno, with 75 stars.

Can I simulate one of these boards using the LM317T before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part