7 open source boards using the MCP23008-E/P

Real designs built with the MCP23008-E/P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the MCP23008-E/P

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP23008-E/P connects to, and the resistors, capacitors and other passives placed on it.

  • The A2 pin is tied to GND on 6 of 7 designs.
  • The A1 pin is tied to GND on 6 of 7 designs.
  • The A0 pin is tied to GND on 6 of 7 designs.
  • The SCL pin has a pull-up to 5V on 4 of 7 designs, most often 10 kΩ.
SCLpin 1Connected to: A connector 57%, the microcontroller 29%
  • Pull-up to 5V on 57% · 10 kΩ (4)
SDApin 2Connected to: A connector 57%, the microcontroller 29%
  • Pull-up to 5V on 57% · 10 kΩ (4)
A2pin 3Connected to: GND 86%
A1pin 4Connected to: GND 86%
A0pin 5Connected to: GND 86%
NCpin 7Connected to: Not connected 100%
VSSpin 9Connected to: GND 100%
GP3pin 13Connected to: A connector 29%
  • Series resistor on 57% · 1.5 kΩ (2), 220 Ω (1), 10 kΩ (1)
GP4pin 14Connected to: A connector 29%
  • Series resistor on 43% · 1.5 kΩ (2), 220 Ω (1)
VDDpin 18Connected to: 5V 86%
  • Decoupling capacitor on 57% · 10 µF (2), 1 µF (1), 100 nF (1)

8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gingham by yiancar, Gingham-USBC by yiancar, Tactile Switch Interface Board by Accessible-AAC and Garden Irrigation Sprinkler Card by vinthewrench.

The MCP23008-E/P in open source designs

The gallery holds 7 open source boards using the MCP23008-E/P from 7 GitHub repositories; a typical one measures about 129.3 × 100 mm and carries around 138 components.

71% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is Gingham by yiancar.

Microcontrollers on boards using the MCP23008-E/P

What boards using the MCP23008-E/P are built for

MCP23008-E/P: common questions

Where can I find a MCP23008-E/P reference design?

Each of the 7 boards on this page is a real design using the MCP23008-E/P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP23008-E/P A2 pin connected?

The A2 pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MCP23008-E/P.

How is the MCP23008-E/P A1 pin connected?

The A1 pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MCP23008-E/P.

How is the MCP23008-E/P A0 pin connected?

The A0 pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MCP23008-E/P.

What parts are used alongside the MCP23008-E/P?

The ATmega328-PU, BA033CC0FP-E2, BME280, MCP9808_MSOP and Teensy4.1 appear in the most repositories here.

Which microcontrollers do boards using the MCP23008-E/P use?

Most are built on AVR/Arduino (2) and NXP (2).

How big is a typical board using the MCP23008-E/P?

The median is 129.3 × 100 mm, and 71% are two-layer designs.

What is the most popular open source board using the MCP23008-E/P?

By GitHub stars, Gingham by yiancar, with 85 stars.

Can I simulate one of these boards using the MCP23008-E/P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part