27 open source boards using the MCP9808_MSOP
Real designs built with the MCP9808_MSOP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Dpsgo
dpiegdon
140 × 100 mm149 parts4LNo license9ESP32
RykerConnect
JanB97
102 × 34 mm31 parts2LGPL-3.0370MHz-Soil-Sensor
jhns-de
49 × 80 mm114 parts4LNo license2NXP
MLU BreakoutV2
ryos17
129.3 × 99 mm138 parts4LNo license1NXP
MLU BreakoutV2
valex2
129.3 × 99 mm138 parts4LNo license1ESP32
Supla ESP32 LAN
jaku2019
209 × 85.5 mm211 parts2LNo license0STM32
Carte Alim
evolutek
115 × 65 mm132 parts2LNo license0RP2040/RP2350
Picoclock
locked
175.8 × 64 mm86 parts2LNo license0BoneIO - relay board
dominikjeske
169 × 102 mm68 parts2LGPL-3.00RP2040/RP2350
Picowater
locked
98 × 56 mm50 parts2LNo license0ESP32
TeamTempSensorEE31 v0 3-preroute
remren
27.4 × 33.7 mm39 parts2LNo license0BoneIO - dimmer LED board 46x5A v0.1
boneIO-eu
197 × 102 mm305 parts2LGPL-3.02ESP32
Watch2-board outline
atctwo
48.6 × 42.9 mm68 partsMIT2Power ManagementV2
ryos17
111 × 110.5 mm129 parts2LNo license1Power ManagementV2
valex2
111 × 110.5 mm129 parts2LNo license1ESP32
TeamTempSensorEE31 v0 3a preroute
remren
27.4 × 33.7 mm39 parts2LNo license0ESP32
Watch2
atctwo
48.6 × 35.6 mm66 partsMIT2NXP
To order
ryos17
151.4 × 80 mm111 parts2LNo license1Power Distribution
valex2
130 × 61 mm68 parts2LNo license1ESP32
TeamTempSensorEE31 v0 4
remren
27.4 × 33.7 mm39 parts2LNo license0ESP32
Watch2-without led tab
atctwo
48.6 × 35.6 mm66 partsMIT2Power ManagementV3 eli
ryos17
98 × 107 mm97 parts2LNo license1Frontpanel
locked
175.8 × 64 mm19 parts2LNo license0Power Distribution
ryos17
151.4 × 80 mm82 parts2LNo license1Perovskite Contact Board
Big-Red-Sat
55.2 × 55.2 mm12 parts2LCC-BY-SA-4.06Power Control Card new
lbrosnan1
100 × 62.5 mm16 parts2LNo license2Power ManagementV3 diode
ryos17
92 × 78 mm39 parts2LNo license1
How designs wire the MCP9808_MSOP
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the MCP9808_MSOP connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 10 of 15 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 10 of 15 designs, most often 4.7 kΩ (then 10 kΩ).
- The A2 pin is tied to GND on 12 of 15 designs (a signal on 3).
- The A1 pin is tied to GND on 12 of 15 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SDApin 1 | Connected to: The microcontroller 40%, a connector 33%, MCP9808_MSOP 27% |
|
| SCLpin 2 | Connected to: The microcontroller 40%, a connector 33%, MCP9808_MSOP 27% |
|
| ALERTpin 3 | Connected to: Not connected 73% · a signal 27% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| A2pin 5 | Connected to: GND 80% · a signal 20% | — |
| A1pin 6 | Connected to: GND 80% · a signal 20% | — |
| A0pin 7 | Connected to: GND 67% · a signal 27% | — |
| VDDpin 8 | Connected to: 3.3V 93% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dpsgo by dpiegdon, Perovskite Contact Board by Big-Red-Sat, RykerConnect by JanB97 and Watch2 by atctwo.
The MCP9808_MSOP in open source designs
The gallery holds 27 open source boards using the MCP9808_MSOP from 15 GitHub repositories; a typical one measures about 110.9 × 65 mm and carries around 68 components.
83% are two-layer designs, the rest use four layers or more, and 26% carry an open source license.
The most starred is Dpsgo by dpiegdon.
Parts used alongside the MCP9808_MSOP
Microcontrollers on boards using the MCP9808_MSOP
What boards using the MCP9808_MSOP are built for
MCP9808_MSOP: common questions
Where can I find a MCP9808_MSOP reference design?
Each of the 27 boards on this page is a real design using the MCP9808_MSOP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP9808_MSOP SDA pin?
The SDA pin has a pull-up to 3.3V on 10 of 15 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 15 open source designs using the MCP9808_MSOP.
What pull-up resistor is used on the MCP9808_MSOP SCL pin?
The SCL pin has a pull-up to 3.3V on 10 of 15 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 15 open source designs using the MCP9808_MSOP.
How is the MCP9808_MSOP A2 pin connected?
The A2 pin is tied to GND on 12 of 15 designs (a signal on 3). Counted from the KiCad layouts of 15 open source designs using the MCP9808_MSOP.
What parts are used alongside the MCP9808_MSOP?
The 74AHC1G04, 74LVC1G08, 74VHC21FT, ACS713ELCTR-30A-T and ACS758LCB-100U-PFF-T appear in the most repositories here.
Which microcontrollers do boards using the MCP9808_MSOP use?
Most are built on ESP32 (8), NXP (3), RP2040/RP2350 (2) and FPGA (1).
How big is a typical board using the MCP9808_MSOP?
The median is 110.9 × 65 mm, and 83% are two-layer designs.
What is the most popular open source board using the MCP9808_MSOP?
By GitHub stars, Dpsgo by dpiegdon, with 9 stars.
Can I simulate one of these boards using the MCP9808_MSOP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.