34 open source boards using the ATmega328-PU
Real designs built with the ATmega328-PU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Torn left
rtitmuss
140.8 × 115.7 mm68 parts2LCC-BY-NC-4.0691AVR/Arduino
Torn Keyboard - Left
EanNewton
140.8 × 115.7 mm68 parts2LMIT178AVR/Arduino
Gingham
yiancar
285.8 × 123.8 mm160 parts2LCC-BY-NC-4.085AVR/Arduino
Rosaline ortho
peej
285.4 × 94.9 mm148 parts2LMIT52AVR/Arduino
Gingham-USBC
yiancar
285.8 × 123.8 mm162 parts2LCC-BY-SA-4.043AVR/Arduino
Alamode
wyolum
85.1 × 55.9 mm75 partsNo license35AVR/Arduino
Rti
cceh
100 × 80 mm54 parts2LNo license15AVR/Arduino
Numpad
str-dst
99.3 × 115.8 mm60 parts2LCC-BY-NC-4.014AVR/Arduino
Beat707
FrankBuss
276.9 × 142.2 mm263 parts2LNo license11AVR/Arduino
FranzBoy
Franzininho
50 × 100 mm43 parts2LNo license9AVR/Arduino
ECG-Simulator
JohanSmets
67.3 × 48.3 mm41 parts2LGPL-3.03AVR/Arduino
Automata Generator Standard
Sirawit7205
246.4 × 127 mm121 parts2LNo license2AVR/Arduino
UZ80
adzierzanowski
231.4 × 159.9 mm112 parts2LNo license2AVR/Arduino
USB Saturn obdev
mark-dawn
79.3 × 47.9 mm17 parts2LGPL-3.02AVR/Arduino
ArduPLC
Reiken3099
101.6 × 101.6 mm86 parts2LCC0-1.01AVR/Arduino
1KVA-SINE-WAVE-POWER-INVERTER
Ogbonna-Joseph
111.1 × 44.5 mm33 parts2LNo license1AVR/Arduino
Fram prototype
uw-madison-chem-shops
91.4 × 66 mm25 parts2LCERN-OHL-P-2.01AVR/Arduino
OSL120557060
n1LS
115.6 × 108 mm80 parts2LNo license0AVR/Arduino
Luciebox v5
hyperlode
78 × 90.5 mm62 parts2LNo license0AVR/Arduino
Vga
rjw57
99.1 × 99.1 mm44 parts2LNo license0AVR/Arduino
Nanpy blinds control
megasaturnv
132.1 × 48.3 mm38 parts2LGPL-3.00AVR/Arduino
ARDUMINI
lmtreser
61 × 69.9 mm27 parts2LNo license0AVR/Arduino
J2o Board
qbancoffee
82.6 × 52.5 mm16 parts2LLGPL-3.0239AVR/Arduino
RFBitBanger
profdc9
152 × 88 mm226 parts2LNo license221AVR/Arduino
Rosaline
peej
285.4 × 94.9 mm137 parts2LMIT52AVR/Arduino
SDR SSB
kholia
85.1 × 71.7 mm70 parts2LNo license15AVR/Arduino
Power cct
AronAyub
108.6 × 145 mm75 parts2LNo license6AVR/Arduino
USB Saturn obdev flat USB
mark-dawn
72.6 × 47.2 mm17 parts2LGPL-3.02AVR/Arduino
RAM
Robert-Riordan-UCD
133 × 58.5 mm57 parts2LCERN-OHL-P-2.00AVR/Arduino
J2o Board
JJaroll
82.6 × 52.5 mm16 parts2LLGPL-3.00AVR/Arduino
Brain board
FrankBuss
100 × 100 mm70 parts2LNo license11AVR/Arduino
Placa J20 - Adaptador VGA iMac G3 DV (traduccion al espanol)
JJaroll
82.6 × 52.5 mm16 parts2LLGPL-3.00AVR/Arduino
ALaMode v3
wyolum
85.1 × 55.9 mm76 partsNo license1AVR/Arduino
Display interface
saktheeswaranswan
96.5 × 55.3 mm7 parts2LMIT0
How designs wire the ATmega328-PU
Read from the KiCad layouts of 30 open source designs, one per repository: what each pin of the ATmega328-PU connects to, and the resistors, capacitors and other passives placed on it.
- The PC6 pin has a pull-up to 5V on 26 of 30 designs, most often 10 kΩ (then 1 kΩ).
- The PB6 pin has a crystal on 26 of 30 designs, most often 16 MHz (then 20 MHz).
- The PB7 pin has a crystal on 26 of 30 designs, most often 16 MHz (then 20 MHz).
- The PB6 pin has a capacitor to GND on 25 of 30 designs, most often 22 pF (then 20 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PC6pin 1 | Connected to: A connector 63% |
|
| PD2pin 4 | Connected to: A connector 23% · not connected 23% |
|
| VCCpin 7 | Connected to: 5V 90% |
|
| GNDpin 8, 22 | Connected to: GND 97% | — |
| PB6pin 9 | Connected to: Signal 100% |
|
| PB7pin 10 | Connected to: Signal 97% |
|
| AVCCpin 20 | Connected to: 5V 83% |
|
| AREFpin 21 | Connected to: Not connected 60% · 5V 20% · a signal 20% | — |
| PC4pin 27 | Connected to: A connector 43% · not connected 27% |
|
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Torn left by rtitmuss, J2o Board by qbancoffee, RFBitBanger by profdc9 and Torn Keyboard - Left by EanNewton.
The ATmega328-PU in open source designs
The gallery holds 34 open source boards using the ATmega328-PU from 30 GitHub repositories; a typical one measures about 100 × 89.3 mm and carries around 65 components.
100% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Torn left by rtitmuss.
Parts used alongside the ATmega328-PU
Microcontrollers on boards using the ATmega328-PU
What boards using the ATmega328-PU are built for
ATmega328-PU: common questions
Where can I find a ATmega328-PU reference design?
Each of the 34 boards on this page is a real design using the ATmega328-PU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ATmega328-PU PC6 pin?
The PC6 pin has a pull-up to 5V on 26 of 30 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 30 open source designs using the ATmega328-PU.
How is the ATmega328-PU PB6 pin connected?
The PB6 pin has a crystal on 26 of 30 designs, most often 16 MHz (then 20 MHz). Counted from the KiCad layouts of 30 open source designs using the ATmega328-PU.
How is the ATmega328-PU PB7 pin connected?
The PB7 pin has a crystal on 26 of 30 designs, most often 16 MHz (then 20 MHz). Counted from the KiCad layouts of 30 open source designs using the ATmega328-PU.
What parts are used alongside the ATmega328-PU?
The 74HC04, 74HC125, DS3231N, LCC110 and LM358N appear in the most repositories here.
Which microcontrollers do boards using the ATmega328-PU use?
Most are built on AVR/Arduino (34).
How big is a typical board using the ATmega328-PU?
The median is 100 × 89.3 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATmega328-PU?
By GitHub stars, Torn left by rtitmuss, with 691 stars.
Can I simulate one of these boards using the ATmega328-PU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.