9 open source boards using the MCP2518FD-xQBB
Real designs built with the MCP2518FD-xQBB, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
HALPI2-hardware
hatlabs
187 × 109 mm541 parts6LCustom license9Raspberry Pi
Masters thesis lora gateway compute module cubesat payload
dpmj
90.2 × 95.9 mm338 parts6LCERN-OHL-S-2.02RevExBot
priyanshu-ogdev
106 × 98 mm60 parts4LApache-2.01Sensor to-CAN
Sarbf1
46 × 20 mm45 parts4LCustom license1STM32
ControlPanelV3S
bartkepl
120 × 75 mm300 parts4LMIT0RP2040/RP2350
Titanrio
ggarciabaez
220.5 × 164.5 mm81 parts4LNo license0Industrial hat rpi4
V2gkr
65 × 56 mm52 parts2LNo license0CAN
AbdullahDxB
50 × 35 mm19 parts2LNo license0Radxa-CM3-carrier
Froggy111
80 × 100 mm46 parts4LNo license1
How designs wire the MCP2518FD-xQBB
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MCP2518FD-xQBB connects to, and the resistors, capacitors and other passives placed on it.
- The OSC2_5 pin has a crystal on 8 of 9 designs, most often 40 MHz (then 20 MHz).
- The OSC2_5 pin has a capacitor to GND on 8 of 9 designs, most often 20 pF (then 22 pF).
- The OSC1_6 pin has a crystal on 8 of 9 designs, most often 40 MHz (then 20 MHz).
- The OSC1_6 pin has a capacitor to GND on 8 of 9 designs, most often 20 pF (then 22 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CLKO/SOF_3pin 3 | Connected to: Not connected 89% | — |
| OSC2_5pin 5 | Connected to: Signal 89% |
|
| OSC1_6pin 6 | Connected to: Signal 100% |
|
| VSS_7pin 7 | Connected to: GND 100% | — |
| INT1/GPIO1_8pin 8 | Connected to: Not connected 78% · a signal 22% | — |
| INT0/GPIO0/XSTBY_9pin 9 | Connected to: Not connected 78% · a signal 22% | — |
| VDD_14pin 14 | Connected to: 3.3V 100% |
|
| VSS_15pin 15 | Connected to: GND 100% | — |
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HALPI2-hardware by hatlabs, Masters thesis lora gateway compute module cubesat payload pcb by dpmj, Radxa-CM3-carrier by Froggy111 and RevExBot by priyanshu-ogdev.
The MCP2518FD-xQBB in open source designs
The gallery holds 9 open source boards using the MCP2518FD-xQBB from 9 GitHub repositories; a typical one measures about 90.2 × 95.9 mm and carries around 60 components.
78% use four copper layers or more, and 33% carry an open source license.
The most starred is HALPI2-hardware by hatlabs.
Parts used alongside the MCP2518FD-xQBB
Microcontrollers on boards using the MCP2518FD-xQBB
What boards using the MCP2518FD-xQBB are built for
MCP2518FD-xQBB: common questions
Where can I find a MCP2518FD-xQBB reference design?
Each of the 9 boards on this page is a real design using the MCP2518FD-xQBB. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP2518FD-xQBB OSC2_5 pin connected?
The OSC2_5 pin has a crystal on 8 of 9 designs, most often 40 MHz (then 20 MHz). Counted from the KiCad layouts of 9 open source designs using the MCP2518FD-xQBB.
How is the MCP2518FD-xQBB OSC1_6 pin connected?
The OSC1_6 pin has a crystal on 8 of 9 designs, most often 40 MHz (then 20 MHz). Counted from the KiCad layouts of 9 open source designs using the MCP2518FD-xQBB.
What decoupling capacitors do designs use on the MCP2518FD-xQBB VDD_14 pin?
The VDD_14 pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the MCP2518FD-xQBB.
Which microcontrollers do boards using the MCP2518FD-xQBB use?
Most are built on RP2040/RP2350 (2), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the MCP2518FD-xQBB?
The median is 90.2 × 95.9 mm, and 22% are two-layer designs.
What is the most popular open source board using the MCP2518FD-xQBB?
By GitHub stars, HALPI2-hardware by hatlabs, with 9 stars.
Can I simulate one of these boards using the MCP2518FD-xQBB before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.