11 open source boards using the MCP4726
Real designs built with the MCP4726, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Analclock v2
sahko123
44 × 28 mm37 parts2LNo license6ESP32
Helix vape
stevensun369
30 × 97 mm77 parts2LNo license1Digital-DC-Load
RedlabsDE
70 × 30 mm66 parts2LNo license0AVR/Arduino
Quantizer
ijnekenamay
30 × 99 mm35 parts2LNo license143ExtendedRangeSupply
esl-epfl
15.3 × 45.8 mm41 parts4LNo license2NA current shunt monitor gum
esl-epfl
15.3 × 45.8 mm30 parts4LNo license11CurrentSource
esl-epfl
15.3 × 45.8 mm34 parts4LNo license21p6V to m1p6V bias gum
esl-epfl
15.2 × 34.3 mm25 parts4LNo license11NA current shunt monitor gum
esl-epfl
15.3 × 45.8 mm30 parts4LNo license2PIC
Test digitale
CarloMara
40.6 × 52.1 mm12 parts2LNo license01p6V to m1p6V bias gum
esl-epfl
15.2 × 34.3 mm25 parts4LNo license2
How designs wire the MCP4726
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP4726 connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pin has a series resistor on 4 of 7 designs, most often 53.6 kΩ (then 470 Ω).
- The VDD pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF.
- The SDA pin has a pull-up to 5V on 4 of 7 designs, most often 4.7 kΩ (then 3.3 kΩ).
- The SCL pin has a pull-up to 5V on 4 of 7 designs, most often 4.7 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: Signal 100% |
|
| VSSpin 2 | Connected to: GND 100% | — |
| VDDpin 3 | Connected to: 3.3V 100% |
|
| SDApin 4 | Connected to: The microcontroller 57%, 24AA02E-OT 29%, a connector 29% |
|
| SCLpin 5 | Connected to: The microcontroller 57%, 24AA02E-OT 29%, a connector 29% |
|
| VREFpin 6 | Connected to: TLV75801PDBV 29%, another IC 29% · not connected 29% · 5V 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Quantizer by ijnekenamay, 1p6V to m1p6V bias gum by esl-epfl, Analclock v2 by sahko123 and 1p6V to m1p6V bias gum by esl-epfl.
The MCP4726 in open source designs
The gallery holds 11 open source boards using the MCP4726 from 7 GitHub repositories; a typical one measures about 15.3 × 45.8 mm and carries around 34 components.
55% use four copper layers or more, and 0% carry an open source license.
The most starred is Quantizer by ijnekenamay.
Parts used alongside the MCP4726
Microcontrollers on boards using the MCP4726
What boards using the MCP4726 are built for
MCP4726: common questions
Where can I find a MCP4726 reference design?
Each of the 11 boards on this page is a real design using the MCP4726. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP4726 VOUT pin?
The VOUT pin has a series resistor on 4 of 7 designs, most often 53.6 kΩ (then 470 Ω). Counted from the KiCad layouts of 7 open source designs using the MCP4726.
What decoupling capacitors do designs use on the MCP4726 VDD pin?
The VDD pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the MCP4726.
What pull-up resistor is used on the MCP4726 SDA pin?
The SDA pin has a pull-up to 5V on 4 of 7 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 7 open source designs using the MCP4726.
What parts are used alongside the MCP4726?
The 24AA02E-OT, ADS1219, INA212AIDCKR, TLV75801PDBV and TPS72301 appear in the most repositories here.
Which microcontrollers do boards using the MCP4726 use?
Most are built on AVR/Arduino (1), ESP32 (1), PIC (1) and RP2040/RP2350 (1).
How big is a typical board using the MCP4726?
The median is 15.3 × 45.8 mm, and 45% are two-layer designs.
What is the most popular open source board using the MCP4726?
By GitHub stars, Quantizer by ijnekenamay, with 143 stars.
Can I simulate one of these boards using the MCP4726 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.