10 open source boards using the MOC3041M
Real designs built with the MOC3041M, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Maxpilot
zefr0g
99.1 × 38.1 mm12 parts2LCERN-OHL-S-2.03ESP32
Lawn sprinkler
adriencarbonaro
135 × 101.5 mm87 parts2LNo license0Microchip SAM
Gaming toaster
ikajdan
112 × 88 mm42 parts2LNo license0NXP
Reflow oven hw
cnpem-emi
160 × 129.8 mm28 parts2LNo license0- schematic only · 55 parts
Standig-899D
andy5211d
55 partsNo license0 AVR/Arduino
MySensors 8FilPilotes
LudovicLemarinel
79 × 98 mm60 parts2LNo license4AVR/Arduino
MySensors FilPilote nrf24
LudovicLemarinel
50 × 50 mm15 parts2LNo license4Basic decoration
maticas-tech-sas
67.2 × 56.5 mm12 parts2LNo license0AVR/Arduino
MySensors FilPilote RFM69
LudovicLemarinel
47.5 × 49 mm14 parts2LNo license4ESP8266
FilPilote
LudovicLemarinel
50 × 40 mm14 parts2LNo license3
How designs wire the MOC3041M
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MOC3041M connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 7 designs, most often 270 Ω (then 1 kΩ).
- Pin 4 has a series resistor on 4 of 7 designs, most often 330 Ω (then 360 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| NCpin 3, 5 | Connected to: Not connected 100% | — |
| Pin 4 | Connected to: MOC3041M 29% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MySensors 8FilPilotes by LudovicLemarinel, FilPilote by LudovicLemarinel, Maxpilot by zefr0g and Lawn sprinkler by adriencarbonaro.
The MOC3041M in open source designs
The gallery holds 10 open source boards using the MOC3041M from 8 GitHub repositories; a typical one measures about 79 × 56.5 mm and carries around 22 components.
100% are two-layer designs, the rest use four layers or more, and 10% carry an open source license.
The most starred is MySensors 8FilPilotes by LudovicLemarinel.
Microcontrollers on boards using the MOC3041M
What boards using the MOC3041M are built for
MOC3041M: common questions
Where can I find a MOC3041M reference design?
Each of the 10 boards on this page is a real design using the MOC3041M. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MOC3041M pin 1?
Pin 1 has a series resistor on 5 of 7 designs, most often 270 Ω (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the MOC3041M.
What resistor goes on the MOC3041M pin 4?
Pin 4 has a series resistor on 4 of 7 designs, most often 330 Ω (then 360 Ω). Counted from the KiCad layouts of 7 open source designs using the MOC3041M.
Which microcontrollers do boards using the MOC3041M use?
Most are built on AVR/Arduino (3), ESP8266 (2), ESP32 (1) and NXP (1).
How big is a typical board using the MOC3041M?
The median is 79 × 56.5 mm, and 100% are two-layer designs.
What is the most popular open source board using the MOC3041M?
By GitHub stars, MySensors 8FilPilotes by LudovicLemarinel, with 4 stars.
Can I simulate one of these boards using the MOC3041M before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.