12 open source boards using the MOC3063M
Real designs built with the MOC3063M, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Socket
eddyem
87 × 71 mm84 parts2LNo license80Inwall relay
slaesh
33.5 × 37.5 mm41 parts2LGPL-3.011STM32
Stm32f0-can mini breakout
NerdyProjects
91.4 × 53.7 mm98 parts2LNo license8ESP8266
ReflowOven
hjf
58.4 × 101.6 mm45 parts2LMIT4- schematic only · 52 parts
Osmofresh quellapro reverse engineering
LostCacher
52 partsMIT1 SmartMeter
MNasser-iono
100.6 × 207.3 mm56 parts2LNo license0STM32
Acid vaporizer
vad32m
98 × 50 mm55 parts2LNo license0ESP32
Esp23 i3 heat thermostat
i3detroit
111 × 65 mm54 parts2LNo license0ESP32
Xiao ac ssr
HarryPehkonen
150 × 45 mm14 parts2LUnlicense0Smart meter
MahmoudNasser9
93 × 191.5 mm57 parts2LNo license0Valhalla-MOD-PSU
csdexter
99.6 × 99.6 mm50 parts2LGPL-3.00Triac fet module
mekatrol
60 × 25 mm11 parts2LNo license0
How designs wire the MOC3063M
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the MOC3063M connects to, and the resistors, capacitors and other passives placed on it.
- Pin 6 has a series resistor on 10 of 11 designs, most often 100 Ω (then 330 Ω).
- Pin 1 has a series resistor on 8 of 11 designs, most often 330 Ω (then 680 Ω).
- Pin 4 has a series resistor on 8 of 11 designs, most often 330 Ω (then 360 Ω).
- Pin 2 is tied to GND on 8 of 11 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 91% |
|
| Pin 2 | Connected to: GND 73% · a signal 27% | — |
| NCpin 3, 5 | Connected to: Not connected 100% | — |
| Pin 4 | Connected to: Signal 100% |
|
| Pin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Socket by eddyem, Inwall relay by slaesh, Stm32f0-can mini breakout by NerdyProjects and ReflowOven by hjf.
The MOC3063M in open source designs
The gallery holds 12 open source boards using the MOC3063M from 12 GitHub repositories; a typical one measures about 93 × 65 mm and carries around 53 components.
100% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.
The most starred is Socket by eddyem.
What boards using the MOC3063M are built for
MOC3063M: common questions
Where can I find a MOC3063M reference design?
Each of the 12 boards on this page is a real design using the MOC3063M. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MOC3063M pin 6?
Pin 6 has a series resistor on 10 of 11 designs, most often 100 Ω (then 330 Ω). Counted from the KiCad layouts of 11 open source designs using the MOC3063M.
What resistor goes on the MOC3063M pin 1?
Pin 1 has a series resistor on 8 of 11 designs, most often 330 Ω (then 680 Ω). Counted from the KiCad layouts of 11 open source designs using the MOC3063M.
What resistor goes on the MOC3063M pin 4?
Pin 4 has a series resistor on 8 of 11 designs, most often 330 Ω (then 360 Ω). Counted from the KiCad layouts of 11 open source designs using the MOC3063M.
Which microcontrollers do boards using the MOC3063M use?
Most are built on STM32 (3), ESP32 (2) and ESP8266 (1).
How big is a typical board using the MOC3063M?
The median is 93 × 65 mm, and 100% are two-layer designs.
What is the most popular open source board using the MOC3063M?
By GitHub stars, Socket by eddyem, with 80 stars.
Can I simulate one of these boards using the MOC3063M before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.