7 open source boards using the PCA9306DC1
Real designs built with the PCA9306DC1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
M.2-FPGA-Accelerator
KaiPereira
22 × 80 mm276 parts6LNo license25RP2040/RP2350
Hardware
seedhammer
205.3 × 78 mm172 parts4LUnlicense9RP2040/RP2350
Wifi interposer
dsi-modchip
51.3 × 21 mm51 parts4LCERN-OHL-S-2.02FPGA
Gammapi zero
vikulin
65 × 30 mm142 parts4LSHL-2.10- schematic only · 562 partsRaspberry Pi
OpenXTCM5-Head-Unit
mibs510
562 parts2LMIT0 FPGA
Anice
hackclub
65.6 × 34 mm91 parts4LNo license2
How designs wire the PCA9306DC1
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the PCA9306DC1 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL1_3 pin has a pull-up to 3.3V on 4 of 6 designs, most often 3.3 kΩ (then 4.7 kΩ).
- The SDA1_4 pin has a pull-up to 3.3V on 4 of 5 designs, most often 3.3 kΩ (then 4.7 kΩ).
- The VREF2_7 pin has a pull-up to 5V on 4 of 5 designs, most often 100 kΩ (then 200 kΩ).
- The SDA2_5 pin has a pull-up to 5V on 3 of 5 designs, most often 4.7 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 83% · a signal 17% | — |
| VREF1_2pin 2 | Connected to: 3.3V 83% · a signal 17% | — |
| SCL1_3pin 3 | Connected to: The microcontroller 67% · GND 17% |
|
| SDA1_4pin 4 | Connected to: The microcontroller 80% |
|
| SDA2_5pin 5 | Connected to: A connector 60% |
|
| SCL2_6pin 6 | Connected to: A connector 60% |
|
| VREF2_7pin 7 | Connected to: Signal 100% |
|
| EN_8pin 8 | Connected to: Signal 60% · 5V 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Icepi zero by cheyao, M.2-FPGA-Accelerator by KaiPereira, Hardware by seedhammer and Wifi interposer by dsi-modchip.
The PCA9306DC1 in open source designs
The gallery holds 7 open source boards using the PCA9306DC1 from 7 GitHub repositories; a typical one measures about 65 × 32 mm and carries around 143 components.
86% use four copper layers or more, and 43% carry an open source license.
The most starred is Icepi zero by cheyao.
Parts used alongside the PCA9306DC1
Microcontrollers on boards using the PCA9306DC1
What boards using the PCA9306DC1 are built for
PCA9306DC1: common questions
Where can I find a PCA9306DC1 reference design?
Each of the 7 boards on this page is a real design using the PCA9306DC1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCA9306DC1 SCL1_3 pin?
The SCL1_3 pin has a pull-up to 3.3V on 4 of 6 designs, most often 3.3 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the PCA9306DC1.
What pull-up resistor is used on the PCA9306DC1 SDA1_4 pin?
The SDA1_4 pin has a pull-up to 3.3V on 4 of 5 designs, most often 3.3 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the PCA9306DC1.
What pull-up resistor is used on the PCA9306DC1 VREF2_7 pin?
The VREF2_7 pin has a pull-up to 5V on 4 of 5 designs, most often 100 kΩ (then 200 kΩ). Counted from the KiCad layouts of 6 open source designs using the PCA9306DC1.
What parts are used alongside the PCA9306DC1?
The FT231XQ, TPD2EUSB30, USBLC6-2SC6, W25Q128JVS and W9825G6KH-6 appear in the most repositories here.
Which microcontrollers do boards using the PCA9306DC1 use?
Most are built on FPGA (4), RP2040/RP2350 (2) and Raspberry Pi (1).
How big is a typical board using the PCA9306DC1?
The median is 65 × 32 mm, and 14% are two-layer designs.
What is the most popular open source board using the PCA9306DC1?
By GitHub stars, Icepi zero by cheyao, with 865 stars.
Can I simulate one of these boards using the PCA9306DC1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.