16 open source boards using the PCA9536D
Real designs built with the PCA9536D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Cm4 motherboard
Twisted-Fields
118 × 117 mm238 parts4LNo license81RP2040/RP2350
Hermes Lite2 IO Connector
jimahlstrom
93 × 53.4 mm116 parts4LNo license55AVR/Arduino
Batterymeter
hb020
106.1 × 29.2 mm143 parts4LNo license20RP2040/RP2350
Karabas go
andykarpov
101.6 × 147.3 mm279 parts4LCC-BY-NC-4.02RP2040/RP2350
ANGAZA ELIMU
R-Mutura
131 × 78.5 mm207 parts4LNo license2ESP32
Universal module
renata7zemanova
100 × 100 mm113 parts2LNo license1ESP32
Rf detector
joshitha-c
71 × 150.5 mm57 parts2LNo license0Main v2
etet100
79.4 × 53.3 mm26 parts2LNo license0- schematic only · 262 partsRaspberry Pi
Pcb qa
xxsahanaxx
262 partsNo license0 AddOnB
freeDSP
391 × 45 mm136 parts2LCC-BY-SA-4.0222Printhead
Fiberprinter
35 × 35 mm63 parts2LNo license4ESP32
Semafor bottom
renata7zemanova
99.9 × 100 mm76 parts2LNo license1Sapphire AnalogMic
ChrisHayward-dev
23.5 × 41.4 mm39 parts2LNo license0Main nodemcu
etet100
51.4 × 66.7 mm16 parts2LNo license0AddOnB
mischuja
391 × 45 mm136 parts2LGPL-3.01Accessory board
felixzero
123.2 × 55.3 mm57 parts2LGPL-3.07
How designs wire the PCA9536D
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the PCA9536D connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 4.7 µF).
- The SCL pin has a pull-up to 3.3V on 7 of 13 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 7 of 13 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IO2pin 3 | Connected to: Signal 92% |
|
| VSSpin 4 | Connected to: GND 100% | — |
| SCLpin 6 | Connected to: A connector 46%, the microcontroller 38% |
|
| SDApin 7 | Connected to: A connector 46%, the microcontroller 38% |
|
| VDDpin 8 | Connected to: 3.3V 85% · a signal 15% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AddOnB by freeDSP, Cm4 motherboard by Twisted-Fields, Hermes Lite2 IO Connector by jimahlstrom and Batterymeter by hb020.
The PCA9536D in open source designs
The gallery holds 16 open source boards using the PCA9536D from 14 GitHub repositories; a typical one measures about 100 × 55.3 mm and carries around 115 components.
67% are two-layer designs, the rest use four layers or more, and 19% carry an open source license.
The most starred is AddOnB by freeDSP.
Parts used alongside the PCA9536D
Microcontrollers on boards using the PCA9536D
What boards using the PCA9536D are built for
PCA9536D: common questions
Where can I find a PCA9536D reference design?
Each of the 16 boards on this page is a real design using the PCA9536D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the PCA9536D VDD pin?
The VDD pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 13 open source designs using the PCA9536D.
What pull-up resistor is used on the PCA9536D SCL pin?
The SCL pin has a pull-up to 3.3V on 7 of 13 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 13 open source designs using the PCA9536D.
What pull-up resistor is used on the PCA9536D SDA pin?
The SDA pin has a pull-up to 3.3V on 7 of 13 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 13 open source designs using the PCA9536D.
What parts are used alongside the PCA9536D?
The ADAU1452WBCPZ, ADS1115IDGSR, CA-IS3050G, ET6226M and FIN1002 appear in the most repositories here.
Which microcontrollers do boards using the PCA9536D use?
Most are built on ESP32 (3), RP2040/RP2350 (3), Raspberry Pi (2) and AVR/Arduino (1).
How big is a typical board using the PCA9536D?
The median is 100 × 55.3 mm, and 67% are two-layer designs.
What is the most popular open source board using the PCA9536D?
By GitHub stars, AddOnB by freeDSP, with 222 stars.
Can I simulate one of these boards using the PCA9536D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.