22 open source boards using the QRE1113GR
Real designs built with the QRE1113GR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Line follower
alientanya
214 × 187.9 mm218 parts2LMIT1ESP32
Wooden Clock - main board
tibm110 × 110 mm183 parts4LNo license1Sensores
AlisonTristao
48.8 × 44 mm57 parts2LNo license1Sensor array
GR3Y-SCALE
80 × 16.5 mm27 parts2LNo license1ESP32
Board fully integrated
lleck
370 × 370 mm234 parts4LNo license0STM32
RM Electronics Central Library
CptEdward-MP
124.5 × 78.3 mm211 parts2LNo license0ESP32
SAVITAR-V2
alexandru-mot
54.9 × 46.3 mm135 parts4LNo license0AVR/Arduino
Line follower
rmingon
93.5 × 97.5 mm84 parts2LNo license0Marble sequencer circuits
felicien-brochu
290 × 51.6 mm53 parts2LNo license0AVR/Arduino
Aipet
state-of-the-art
11.5 × 10 mm14 parts2LNo license0ESP32
PercussiveInterface-3
lleck
460 × 97.7 mm105 parts2LNo license0Sensor garis
Mervs111
94.4 × 51 mm39 parts2LNo license0Line
tr0fin0
7.5 × 14 mm4 parts2LGPL-3.03Line
equipe-paralela
7.5 × 14 mm4 parts2LGPL-3.01Amod m
gallicchio
100 × 100 mm207 parts4LCERN-OHL-P-2.00ESP32
PercussiveInterface-3.1
lleck
460 × 97.7 mm105 parts4LNo license0Sensors16 MagicAlonso
JRegi
140 × 28.5 mm62 parts2LMIT0ESP32
Main board new-3.2
lleck
369.4 × 107.4 mm82 parts4LNo license0Amod b
gallicchio
100 × 100 mm143 parts4LCERN-OHL-P-2.00CustomML2
RoboJackets
10 × 22 mm7 parts2LMIT9ESP32
Main board-3.2
lleck
390 × 390 mm36 parts4LNo license0ESP32
Main board 4 jlc-3.2
lleck
369.4 × 107.4 mm36 parts4LNo license0
How designs wire the QRE1113GR
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the QRE1113GR connects to, and the resistors, capacitors and other passives placed on it.
- The GND pin has a pull-up to 3.3V on 13 of 16 designs, most often 10 kΩ (then 47 kΩ).
- Pin 4 is tied to GND on 14 of 15 designs.
- The A pin has a pull-up to 3.3V on 11 of 16 designs, most often 100 Ω (then 150 Ω).
- The K pin is tied to GND on 12 of 16 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Apin 1 | Connected to: Signal 75% · VCC 25% |
|
| Kpin 2 | Connected to: GND 75% · a signal 19% | — |
| GNDpin 3 | Connected to: A connector 31% |
|
| Pin 4 | Connected to: GND 93% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CustomML2 by RoboJackets, Line by tr0fin0, Line follower-PCB by alientanya and Sensores by AlisonTristao.
The QRE1113GR in open source designs
The gallery holds 22 open source boards using the QRE1113GR from 16 GitHub repositories; a typical one measures about 105 × 87.9 mm and carries around 72 components.
59% are two-layer designs, the rest use four layers or more, and 32% carry an open source license.
The most starred is CustomML2 by RoboJackets.
Parts used alongside the QRE1113GR
Microcontrollers on boards using the QRE1113GR
What boards using the QRE1113GR are built for
QRE1113GR: common questions
Where can I find a QRE1113GR reference design?
Each of the 22 boards on this page is a real design using the QRE1113GR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the QRE1113GR GND pin?
The GND pin has a pull-up to 3.3V on 13 of 16 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 16 open source designs using the QRE1113GR.
How is the QRE1113GR pin 4 connected?
Pin 4 is tied to GND on 14 of 15 designs. Counted from the KiCad layouts of 16 open source designs using the QRE1113GR.
What pull-up resistor is used on the QRE1113GR A pin?
The A pin has a pull-up to 3.3V on 11 of 16 designs, most often 100 Ω (then 150 Ω). Counted from the KiCad layouts of 16 open source designs using the QRE1113GR.
What parts are used alongside the QRE1113GR?
The 74HC4067, TCRT5000L and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the QRE1113GR use?
Most are built on ESP32 (8), AVR/Arduino (2) and STM32 (2).
How big is a typical board using the QRE1113GR?
The median is 105 × 87.9 mm, and 59% are two-layer designs.
What is the most popular open source board using the QRE1113GR?
By GitHub stars, CustomML2 by RoboJackets, with 9 stars.
Can I simulate one of these boards using the QRE1113GR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.