10 open source boards using the TCRT5000L
Real designs built with the TCRT5000L, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Line follower
alientanya
214 × 187.9 mm218 parts2LMIT1STM32
RM Electronics Central Library
CptEdward-MP
124.5 × 78.3 mm211 parts2LNo license0Motor Health Monitoring 8051
YUKESH0620
135.2 × 73.1 mm99 parts4LMIT0AVR/Arduino
Obstacle sensor with easyC-hardware design
SolderedElectronics
38 × 22 mm20 parts2LTAPR-OHL-1.00AVR/Arduino
Soldered-Obstacle sensor with easyC-hardware design
test-gh-syncer2
38 × 22 mm20 parts2LTAPR-OHL-1.00AVR/Arduino
Obstacle sensor qwiic hardware design
SolderedElectronics
38 × 22 mm20 parts2LTAPR-OHL-1.00Obstacle sensor-TCRT5000-breakout hardware design
SolderedElectronics
22 × 22 mm13 parts2LTAPR-OHL-1.00Line following
enph253-2025-team5
62 × 47 mm13 parts2LGPL-3.00Soldered-Obstacle sensor-TCRT5000-breakout hardware design
test-gh-syncer2
22 × 22 mm13 parts2LTAPR-OHL-1.00MiAM TCRT5000L
14chanwa
10.6 × 12.2 mm3 parts2LNo license0
How designs wire the TCRT5000L
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the TCRT5000L connects to, and the resistors, capacitors and other passives placed on it.
- The ANODE pin has a pull-up to 3.3V on 5 of 5 designs, most often 150 Ω (then 100 Ω).
- Pin A has a pull-up to 3.3V on 5 of 5 designs, most often 1 kΩ (then 300 Ω).
- Pin Coll has a capacitor to GND on 5 of 5 designs, most often 100 nF.
- Pin Coll has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| COLLECTORpin 1 | Connected to: A connector 40% |
|
| EMITTERpin 2 | Connected to: GND 100% | — |
| CATHODEpin 3 | Connected to: GND 100% | — |
| ANODEpin 4 | Connected to: Signal 100% |
|
| Pin A | Connected to: Signal 100% |
|
| Pin Cath | Connected to: GND 100% | — |
| Pin Coll | Connected to: LM393 100%, the microcontroller 60% |
|
| Pin E | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Line follower-PCB by alientanya, MiAM TCRT5000L by 14chanwa, RM Electronics Central Library by CptEdward-MP and Line following pcb by enph253-2025-team5.
The TCRT5000L in open source designs
The gallery holds 10 open source boards using the TCRT5000L from 10 GitHub repositories; a typical one measures about 38 × 22 mm and carries around 20 components.
90% are two-layer designs, the rest use four layers or more, and 80% carry an open source license.
The most starred is Line follower-PCB by alientanya.
Parts used alongside the TCRT5000L
Microcontrollers on boards using the TCRT5000L
What boards using the TCRT5000L are built for
TCRT5000L: common questions
Where can I find a TCRT5000L reference design?
Each of the 10 boards on this page is a real design using the TCRT5000L. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCRT5000L ANODE pin?
The ANODE pin has a pull-up to 3.3V on 5 of 5 designs, most often 150 Ω (then 100 Ω). Counted from the KiCad layouts of 10 open source designs using the TCRT5000L.
What pull-up resistor is used on the TCRT5000L pin A?
Pin A has a pull-up to 3.3V on 5 of 5 designs, most often 1 kΩ (then 300 Ω). Counted from the KiCad layouts of 10 open source designs using the TCRT5000L.
How is the TCRT5000L pin Coll connected?
Pin Coll has a capacitor to GND on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 10 open source designs using the TCRT5000L.
What parts are used alongside the TCRT5000L?
The LM393, ATTINY404-SSNR, 74HC4067 and QRE1113GR appear in the most repositories here.
Which microcontrollers do boards using the TCRT5000L use?
Most are built on AVR/Arduino (3) and STM32 (2).
How big is a typical board using the TCRT5000L?
The median is 38 × 22 mm, and 90% are two-layer designs.
What is the most popular open source board using the TCRT5000L?
By GitHub stars, Line follower-PCB by alientanya, with 1 stars.
Can I simulate one of these boards using the TCRT5000L before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.