12 open source boards using the STLINK-V3MODS
Real designs built with the STLINK-V3MODS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STLinkV3 Adapter
yingchaotw
32 × 48.6 mm10 parts2LMIT9STM32
VCU
formulaslug
92.5 × 101.6 mm202 parts4LNo license7STM32
Zirconia
viola0222
39 × 91 mm90 parts2LApache-2.03STM32
RyanShalini SmartPDM
LHRIC
149.7 × 158.4 mm235 parts4LNo license2STM32
Relock Artiq
KLFAMO
161 × 100 mm375 parts4LNo license0STM32
LightProcessor old
K0iNguyen
181.5 × 190.8 mm149 parts4LNo license0STM32
STM32G474CET 260226
takushio2525
39 × 91 mm90 parts2LNo license0STM32
PAMI TEAM SCRAT FINAL V2.1
YaayY360
60 × 90 mm68 parts4LNo license0STM32
TBB
formulaslug
139.7 × 63.5 mm159 parts4LNo license7STM32
LightProcessor
K0iNguyen
192.1 × 182.1 mm127 parts4LNo license0STM32
LightProcessor preFreeRoute
K0iNguyen
199.5 × 177.1 mm127 parts4LNo license0NOGLINK
berkeleyauv
19.5 × 30.8 mm22 parts2LGPL-3.03
How designs wire the STLINK-V3MODS
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the STLINK-V3MODS connects to, and the resistors, capacitors and other passives placed on it.
- The T_SW_DIR pin is left unconnected on 9 of 9 designs.
- The BRIDGE_UART_RX pin is left unconnected on 7 of 9 designs (a signal on 2).
- The BRIDGE_I2C_SDA pin is left unconnected on 7 of 9 designs (a signal on 2).
- The BRIDGE_UART_CTS pin is left unconnected on 6 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BRIDGE_UART_RXpin 1 | Connected to: Not connected 78% · a signal 22% | — |
| BRIDGE_UART_CTSpin 2 | Connected to: Not connected 86% | — |
| BRIDGE_UART_RTSpin 3 | Connected to: Not connected 86% | — |
| BRIDGE_SPI_CLKpin 7 | Connected to: Not connected 71% · a signal 29% | — |
| GND_2pin 8 | Connected to: GND 100% | — |
| BRIDGE_CAN_RXpin 9 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_CAN_TXpin 10 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_UART_TXpin 11 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_SPI_NSSpin 14 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_I2C_SCLpin 16 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_I2C_SDApin 17 | Connected to: Not connected 78% · a signal 22% | — |
| BRIDGE_GPIO0pin 18 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_GPIO1pin 19 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_GPIO2pin 20 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_GPIO3pin 21 | Connected to: Not connected 71% · a signal 29% | — |
| BRIDGE_SPI_MISOpin 23 | Connected to: Not connected 71% · a signal 29% | — |
| GNDpin 24 | Connected to: GND 78% · a signal 22% | — |
| BRIDGE_SPI_MOSIpin 25 | Connected to: Not connected 71% · a signal 29% | — |
| GND2pin 26 | Connected to: GND 100% | — |
| GND3pin 27 | Connected to: GND 100% | — |
| T_JTDI/NCpin 28 | Connected to: Not connected 86% | — |
| GND4pin 29 | Connected to: GND 100% | — |
| T_NRSTpin 31 | Connected to: A connector 57%, the microcontroller 43% |
|
| T_SW_DIRpin 32 | Connected to: Not connected 100% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include STLinkV3 Adapter by yingchaotw, TBB by formulaslug, NOGLINK by berkeleyauv and Zirconia by viola0222.
The STLINK-V3MODS in open source designs
The gallery holds 12 open source boards using the STLINK-V3MODS from 9 GitHub repositories; a typical one measures about 116.1 × 95.5 mm and carries around 127 components.
67% use four copper layers or more, and 25% carry an open source license.
The most starred is STLinkV3 Adapter by yingchaotw.
Parts used alongside the STLINK-V3MODS
Microcontrollers on boards using the STLINK-V3MODS
What boards using the STLINK-V3MODS are built for
STLINK-V3MODS: common questions
Where can I find a STLINK-V3MODS reference design?
Each of the 12 boards on this page is a real design using the STLINK-V3MODS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the STLINK-V3MODS T_SW_DIR pin connected?
The T_SW_DIR pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the STLINK-V3MODS.
How is the STLINK-V3MODS BRIDGE_UART_RX pin connected?
The BRIDGE_UART_RX pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the STLINK-V3MODS.
How is the STLINK-V3MODS BRIDGE_I2C_SDA pin connected?
The BRIDGE_I2C_SDA pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the STLINK-V3MODS.
What parts are used alongside the STLINK-V3MODS?
The DRV8836DSSR, ENCODER_CONNECT_IC, ENCODER_CONNECT_PCB, ICM-42688-P and LP5907MFX-3.0/NOPB appear in the most repositories here.
Which microcontrollers do boards using the STLINK-V3MODS use?
Most are built on STM32 (10).
How big is a typical board using the STLINK-V3MODS?
The median is 116.1 × 95.5 mm, and 33% are two-layer designs.
What is the most popular open source board using the STLINK-V3MODS?
By GitHub stars, STLinkV3 Adapter by yingchaotw, with 9 stars.
Can I simulate one of these boards using the STLINK-V3MODS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.