7 open source boards using the T-DISPLAY-S3
Real designs built with the T-DISPLAY-S3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NerdOCTAXE-Gamma
Patsch91
200 × 190 mm446 parts6LCERN-OHL-S-2.093NerdOCTAXE-Plus
Patsch91
155.5 × 130 mm290 parts4LCERN-OHL-S-2.033NerdQX
IxTechCrypto
89 × 184 mm217 parts6LCERN-OHL-S-2.027Mainboard v2
shurik179
86 × 62 mm28 parts2LMIT3NerdOCTAXE-Gamma
powerminingio
200 × 190 mm312 parts6LCERN-OHL-S-2.00Nerdqaxe+
shufps
89 × 152 mm183 parts4LCERN-OHL-S-2.0244Nerdqaxe+
imcmurray
89 × 152 mm183 parts4LNo license0
How designs wire the T-DISPLAY-S3
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the T-DISPLAY-S3 connects to, and the resistors, capacitors and other passives placed on it.
- The GPIO11 pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ.
- The GPIO13 pin has a resistor to GND on 6 of 7 designs, most often 10 kΩ.
- The GPIO16 pin is left unconnected on 7 of 7 designs.
- The GPIO21 pin is left unconnected on 7 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 3Vpin 1, 13 | Connected to: 3.3V 79% | — |
| GPIO11pin 6 | Connected to: TPS53647 71% |
|
| GPIO12pin 7 | Connected to: Not connected 71% · a signal 29% | — |
| GPIO13pin 8 | Connected to: MCP1824T-0802E 86%, MCP1824T-1202E 57%, MCP1824T-1802E 29% |
|
| NCpin 9, 10, 16 | Connected to: Not connected 95% | — |
| GNDpin 11, 14, 15, 23, 24 | Connected to: GND 94% | — |
| GPIO16pin 17 | Connected to: Not connected 100% | — |
| GPIO21pin 18 | Connected to: Not connected 100% | — |
| GPIO44pin 21 | Connected to: EMC2302-1 86%, TMP1075 86%, TPS53647 57% |
|
| GPIO43pin 22 | Connected to: EMC2302-1 86%, TMP1075 86%, TPS53647 57% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Nerdqaxe+ by shufps, NerdOCTAXE-Gamma by Patsch91, NerdOCTAXE-Plus by Patsch91 and NerdQX by IxTechCrypto.
The T-DISPLAY-S3 in open source designs
The gallery holds 7 open source boards using the T-DISPLAY-S3 from 7 GitHub repositories; a typical one measures about 89 × 152 mm and carries around 217 components.
86% use four copper layers or more, and 86% carry an open source license.
The most starred is Nerdqaxe+ by shufps.
Parts used alongside the T-DISPLAY-S3
What boards using the T-DISPLAY-S3 are built for
T-DISPLAY-S3: common questions
Where can I find a T-DISPLAY-S3 reference design?
Each of the 7 boards on this page is a real design using the T-DISPLAY-S3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the T-DISPLAY-S3 GPIO11 pin?
The GPIO11 pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the T-DISPLAY-S3.
What resistor goes on the T-DISPLAY-S3 GPIO13 pin?
The GPIO13 pin has a resistor to GND on 6 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the T-DISPLAY-S3.
How is the T-DISPLAY-S3 GPIO16 pin connected?
The GPIO16 pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the T-DISPLAY-S3.
What parts are used alongside the T-DISPLAY-S3?
The 25MHZ, AP3211, CSD95472Q5MC, EMC2302-1 and MCP1824T-0802E appear in the most repositories here.
How big is a typical board using the T-DISPLAY-S3?
The median is 89 × 152 mm, and 14% are two-layer designs.
What is the most popular open source board using the T-DISPLAY-S3?
By GitHub stars, Nerdqaxe+ by shufps, with 244 stars.
Can I simulate one of these boards using the T-DISPLAY-S3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.