15 open source boards using the AP3211
Real designs built with the AP3211, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Qaxe
shufps
89 × 137 mm192 parts4LCERN-OHL-S-2.0244NerdOCTAXE-Gamma
Patsch91
200 × 190 mm446 parts6LCERN-OHL-S-2.093STM32
Radar v2
ckflight
90.2 × 40 mm264 parts4LGPL-3.055NerdOCTAXE-Plus
Patsch91
155.5 × 130 mm290 parts4LCERN-OHL-S-2.033NerdQX
IxTechCrypto
89 × 184 mm217 parts6LCERN-OHL-S-2.027STM32
Radar v2
TonyStark2007
90.2 × 40 mm264 parts4LGPL-3.015PC-AXE
aadhi1014
312 × 111.2 mm533 parts6LTAPR-OHL-1.09Microchip SAM
Mod1base
semianalog
100 × 100 mm110 parts2LCC0-1.02NerdOCTAXE-Gamma
powerminingio
200 × 190 mm312 parts6LCERN-OHL-S-2.00STM32
Qaxe
imcmurray
89 × 137 mm192 parts4LNo license0AVR/Arduino
Environmental-Data-Acquisition-System-Hardware
jscastonguay
88.4 × 68.1 mm43 parts2LMIT0Nerdqaxe+
shufps
89 × 152 mm183 parts4LCERN-OHL-S-2.0244Nerdqaxe+
imcmurray
89 × 152 mm183 parts4LNo license0STM32
Radar MCU
ckflight
36.9 × 32.9 mm98 parts4LGPL-3.055STM32
Radar MCU
TonyStark2007
36.9 × 32.9 mm98 parts4LGPL-3.015
How designs wire the AP3211
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the AP3211 connects to, and the resistors, capacitors and other passives placed on it.
- The BS pin has a series capacitor on 11 of 11 designs, most often 10 nF (then 100 nF).
- The FB pin has a resistor to GND on 11 of 11 designs, most often 16.2 kΩ (then 4.7 kΩ).
- The SW pin has a series capacitor on 11 of 11 designs, most often 10 nF (then 100 nF).
- The SW pin has a inductor on 11 of 11 designs, most often 4.7 µH (then 6.8 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BSpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FBpin 3 | Connected to: Signal 100% |
|
| ENpin 4 | Connected to: 12V 73% · a signal 27% | — |
| INpin 5 | Connected to: 12V 73% · a signal 27% | — |
| SWpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Qaxe by shufps, NerdOCTAXE-Gamma by Patsch91, Radar MCU by ckflight and NerdOCTAXE-Plus by Patsch91.
The AP3211 in open source designs
The gallery holds 15 open source boards using the AP3211 from 11 GitHub repositories; a typical one measures about 89 × 130 mm and carries around 192 components.
87% use four copper layers or more, and 87% carry an open source license.
The most starred is Qaxe by shufps.
Parts used alongside the AP3211
Microcontrollers on boards using the AP3211
What boards using the AP3211 are built for
AP3211: common questions
Where can I find a AP3211 reference design?
Each of the 15 boards on this page is a real design using the AP3211. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP3211 BS pin connected?
The BS pin has a series capacitor on 11 of 11 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 11 open source designs using the AP3211.
What resistor goes on the AP3211 FB pin?
The FB pin has a resistor to GND on 11 of 11 designs, most often 16.2 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 11 open source designs using the AP3211.
How is the AP3211 SW pin connected?
The SW pin has a series capacitor on 11 of 11 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 11 open source designs using the AP3211.
What parts are used alongside the AP3211?
The 25MHZ, CSD95472Q5MC, MCP1824T-0802E, TXU0304PW and EMC2302-1 appear in the most repositories here.
Which microcontrollers do boards using the AP3211 use?
Most are built on STM32 (6), AVR/Arduino (1) and Microchip SAM (1).
How big is a typical board using the AP3211?
The median is 89 × 130 mm, and 13% are two-layer designs.
What is the most popular open source board using the AP3211?
By GitHub stars, Qaxe by shufps, with 244 stars.
Can I simulate one of these boards using the AP3211 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.