21 open source boards using the DS3231

Real designs built with the DS3231, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the DS3231

Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the DS3231 connects to, and the resistors, capacitors and other passives placed on it.

  • The RST pin is left unconnected on 11 of 17 designs (a signal on 6).
  • The SDA pin has a pull-up to 3.3V on 5 of 9 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL pin has a pull-up to 3.3V on 5 of 9 designs, most often 4.7 kΩ (then 10 kΩ).
RSTpin 4Connected to: Not connected 65% · a signal 35%
GNDpin 5, 6, 7, 8, 9, 10, 11, 12, 13Connected to: GND 65% · not connected 21%
SDApin 15Connected to: The microcontroller 67%, a connector 22%
  • Pull-up to 3.3V on 56% · 4.7 kΩ (3), 10 kΩ (1), 3.3 kΩ (1)
SCLpin 16Connected to: The microcontroller 67%, a connector 22%
  • Pull-up to 3.3V on 56% · 4.7 kΩ (3), 10 kΩ (1), 3.3 kΩ (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LargeWordClock by LikeClockwork, OTlight by opeRaptor, Ourglass by photomattmills and SpineTime Controller Board by DaringCuteSeal.

The DS3231 in open source designs

The gallery holds 21 open source boards using the DS3231 from 19 GitHub repositories; a typical one measures about 100 × 60 mm and carries around 46 components.

85% are two-layer designs, the rest use four layers or more, and 24% carry an open source license.

The most starred is LargeWordClock by LikeClockwork.

Parts used alongside the DS3231

Microcontrollers on boards using the DS3231

DS3231: common questions

Where can I find a DS3231 reference design?

Each of the 21 boards on this page is a real design using the DS3231. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the DS3231 RST pin connected?

The RST pin is left unconnected on 11 of 17 designs (a signal on 6). Counted from the KiCad layouts of 17 open source designs using the DS3231.

What pull-up resistor is used on the DS3231 SDA pin?

The SDA pin has a pull-up to 3.3V on 5 of 9 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 17 open source designs using the DS3231.

What pull-up resistor is used on the DS3231 SCL pin?

The SCL pin has a pull-up to 3.3V on 5 of 9 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 17 open source designs using the DS3231.

What parts are used alongside the DS3231?

The K155ID1, TLP627 and IN-14 appear in the most repositories here.

Which microcontrollers do boards using the DS3231 use?

Most are built on AVR/Arduino (4), ESP8266 (3), ESP32 (2) and STM32 (2).

How big is a typical board using the DS3231?

The median is 100 × 60 mm, and 85% are two-layer designs.

What is the most popular open source board using the DS3231?

By GitHub stars, LargeWordClock by LikeClockwork, with 6 stars.

Can I simulate one of these boards using the DS3231 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part