8 open source boards using the TPS62410DRCR
Real designs built with the TPS62410DRCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
- schematic only · 414 partsNXP
Illacceptanything
illacceptanything
414 partsMIT2.0k FPGA
Hackrf pro
greatscottgadgets
120 × 75 mm503 parts6LCERN-OHL-P-2.063Allen wireless
allenyin
55.6 × 33 mm113 partsNo license5NXP
HackRf-Circuit-Board
GitByKaliMeNope
120 × 75 mm439 parts4LCERN-OHL-P-2.01NXP
${TITLE}
Josephrp
120 × 75 mm340 parts4LCustom license12NXP
${TITLE}
greearb
120 × 75 mm340 parts4LGPL-2.01NXP
${TITLE}
JensLiu
120 × 75 mm340 parts4LGPL-2.01NXP
${TITLE}
deepin-community
120 × 75 mm340 parts4LGPL-2.00
How designs wire the TPS62410DRCR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS62410DRCR connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ2 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 180 kΩ).
- The VIN pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF).
- The DEF1 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 180 kΩ).
- The SW1 pin has a inductor on 7 of 7 designs, most often 4.7 µH (then 2.2 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PPpin 0 | Connected to: GND 100% | — |
| ADJ2pin 1 | Connected to: Signal 100% |
|
| MODE/DATApin 2 | Connected to: Signal 86% |
|
| VINpin 3 | Connected to: VIN 100% |
|
| FB1pin 4 | Connected to: Signal 71% · VCC 29% |
|
| DEF1pin 5 | Connected to: Signal 100% |
|
| SW1pin 6 | Connected to: Signal 100% |
|
| EN1pin 7 | Connected to: Signal 86% |
|
| GNDpin 8 | Connected to: GND 100% | — |
| EN2pin 9 | Connected to: A connector 71%, the microcontroller 71% · 1.2V 29% |
|
| SW2pin 10 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hackrf pro by greatscottgadgets, ${TITLE} by Josephrp, Allen wireless by allenyin and HackRf-Circuit-Board-KiCad by GitByKaliMeNope.
The TPS62410DRCR in open source designs
The gallery holds 8 open source boards using the TPS62410DRCR from 8 GitHub repositories; a typical one measures about 120 × 75 mm and carries around 340 components.
100% use four copper layers or more, and 75% carry an open source license.
The most starred is Illacceptanything by illacceptanything.
Parts used alongside the TPS62410DRCR
What boards using the TPS62410DRCR are built for
TPS62410DRCR: common questions
Where can I find a TPS62410DRCR reference design?
Each of the 8 boards on this page is a real design using the TPS62410DRCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS62410DRCR ADJ2 pin?
The ADJ2 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 180 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS62410DRCR.
What decoupling capacitors do designs use on the TPS62410DRCR VIN pin?
The VIN pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the TPS62410DRCR.
What resistor goes on the TPS62410DRCR DEF1 pin?
The DEF1 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 180 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS62410DRCR.
What parts are used alongside the TPS62410DRCR?
The RFFC5072TR7, DEA162400HT-8004B1, LP0603A1880ANTR, LPC4320FBD144,551 and MGA-81563-TR1G appear in the most repositories here.
Which microcontrollers do boards using the TPS62410DRCR use?
Most are built on NXP (6) and FPGA (1).
How big is a typical board using the TPS62410DRCR?
The median is 120 × 75 mm, and 0% are two-layer designs.
What is the most popular open source board using the TPS62410DRCR?
By GitHub stars, Illacceptanything by illacceptanything, with 1,961 stars.
Can I simulate one of these boards using the TPS62410DRCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.