19 open source boards using the 25LCxxx
Real designs built with the 25LCxxx, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
M68k
annoyatron255
100 × 100 mm105 parts2LNo license24FPGA
Dmgplus
Spritetm
78.5 × 80 mm108 parts2LNo license19Microchip SAM
Sammy
openinput-fw
25 × 45 mm60 parts4LCERN-OHL-P-2.09STM32
OpenEFI rev4 bkp
Churrosoft
164 × 118 mm317 parts4LCERN-OHL-S-2.08Microchip SAM
Big sammy
openinput-fw
25 × 45 mm60 parts4LCERN-OHL-P-2.07AVR/Arduino
Nova 1200 front panel
ForgottenMachines
397.5 × 119.4 mm203 parts2LNo license5Arduino UNO Experimental Shield
ffich
68.6 × 53.3 mm68 parts4LMIT4STM32
V1
Churrosoft
265.5 × 132.3 mm267 parts2LMIT1PIC
PIC DEV BOARD
anshukumar146
140.7 × 128.5 mm102 parts4LNo license1ESP8266
Lightball
Jana-Marie
42.6 × 20.3 mm46 parts2LNo license0STM32
OpenEFI rev4
Churrosoft
164 × 118 mm257 parts4LCERN-OHL-S-2.08STM32
UEFI
Churrosoft
99 × 113 mm228 parts4LCERN-OHL-S-2.08RISC-V
Psram addon
Stary2001
22.8 × 23.9 mm16 parts2LCERN-OHL-P-2.02D lev main rounded
wormyrocks
175.3 × 163.3 mm114 parts4LNo license0PIC
Smu subfront 1
jaromir-sukuba
137 × 62 mm56 parts2LNo license188STM32
STM32F rev3
Churrosoft
159.6 × 99.6 mm171 parts4LCERN-OHL-S-2.08STM32
ΜEFI rev2
Churrosoft
99.9 × 99.3 mm151 parts4LCERN-OHL-S-2.08Flash sop lotes rev3
DangerousPrototypes
22.5 × 37.8 mm10 parts2LMIT124Flash wson rev3
DangerousPrototypes
22.5 × 37.8 mm10 parts2LMIT124
How designs wire the 25LCxxx
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the 25LCxxx connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 14 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 64%, a connector 21% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| VCCpin 8 | Connected to: 3.3V 86% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Smu subfront 1 by jaromir-sukuba, Flash sop lotes rev3 by DangerousPrototypes, M68k by annoyatron255 and Dmgplus by Spritetm.
The 25LCxxx in open source designs
The gallery holds 19 open source boards using the 25LCxxx from 14 GitHub repositories; a typical one measures about 99.9 × 99.3 mm and carries around 105 components.
53% use four copper layers or more, and 63% carry an open source license.
The most starred is Smu subfront 1 by jaromir-sukuba.
Parts used alongside the 25LCxxx
What boards using the 25LCxxx are built for
25LCxxx: common questions
Where can I find a 25LCxxx reference design?
Each of the 19 boards on this page is a real design using the 25LCxxx. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 25LCxxx VCC pin?
The VCC pin has a decoupling capacitor on 7 of 14 designs, most often 100 nF. Counted from the KiCad layouts of 14 open source designs using the 25LCxxx.
What parts are used alongside the 25LCxxx?
The 74LVC1G17, MIC5504-3.3YM5, ADUM4160, AMS1117-3.3 and iCE40-HX4K-TQ144 appear in the most repositories here.
Which microcontrollers do boards using the 25LCxxx use?
Most are built on STM32 (6), FPGA (2), PIC (2) and Microchip SAM (2).
How big is a typical board using the 25LCxxx?
The median is 99.9 × 99.3 mm, and 47% are two-layer designs.
What is the most popular open source board using the 25LCxxx?
By GitHub stars, Smu subfront 1 by jaromir-sukuba, with 188 stars.
Can I simulate one of these boards using the 25LCxxx before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.