12 open source boards using the 93LC56B
Real designs built with the 93LC56B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pinpoint core
lab11
58.4 × 50 mm111 parts2LApache-2.0144Ftdi jtag programmer
anthony-bernaert
44 × 64 mm96 parts4LCERN-OHL-P-2.074STM32
ASPECT2
xboxoneresearch
60 × 60 mm116 parts4LNo license17FPGA
Eth4k hardware
theta-machines
98 × 58 mm132 parts4LCERN-OHL-W-2.04FPGA
Xc17 prom prog
msinger
123 × 95 mm281 parts2LCC-BY-SA-4.03FPGA
Controller Board
MichalVarsanyi
85 × 85 mm291 parts6LMIT1Radioberry juice
OE9SAU
65 × 56 mm87 parts2LNo license4FPGA
Programmer Sensor Stencil
MichalVarsanyi
85 × 15.8 mm118 parts2LMIT1Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675FPGA
VoxSense Sensor Board
MichalVarsanyi
85 × 15.8 mm92 parts4LMIT1Radioberry juice
saktheeswaranswan
65 × 56 mm87 parts2LNo license0ESP32
Integrated circuits
LilyTronics
70 × 79 mm35 parts2LGPL-3.02
How designs wire the 93LC56B
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the 93LC56B connects to, and the resistors, capacitors and other passives placed on it.
- The DO pin has a pull-up to 3.3V on 9 of 9 designs, most often 10 kΩ (then 12 kΩ).
- The DI pin has a series resistor on 9 of 9 designs, most often 2.2 kΩ (then 2 kΩ).
- The VCC pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF (then 10 µF).
- The DO pin has a series resistor on 7 of 9 designs, most often 2.2 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| DOpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 78% · a signal 22% | — |
| DIpin 3 | Connected to: FT2232HL 67% |
|
| CLKpin 4 | Connected to: FT2232HL 56% |
|
| CSpin 5 | Connected to: FT2232HL 56% · GND 22% |
|
| VCCpin 6 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Radioberry juice by pa3gsb, Pinpoint core by lab11, Ftdi jtag programmer by anthony-bernaert and ASPECT2 by xboxoneresearch.
The 93LC56B in open source designs
The gallery holds 12 open source boards using the 93LC56B from 10 GitHub repositories; a typical one measures about 67.5 × 57 mm and carries around 104 components.
58% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is Radioberry juice by pa3gsb.
Parts used alongside the 93LC56B
What boards using the 93LC56B are built for
93LC56B: common questions
Where can I find a 93LC56B reference design?
Each of the 12 boards on this page is a real design using the 93LC56B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the 93LC56B DO pin?
The DO pin has a pull-up to 3.3V on 9 of 9 designs, most often 10 kΩ (then 12 kΩ). Counted from the KiCad layouts of 9 open source designs using the 93LC56B.
What resistor goes on the 93LC56B DI pin?
The DI pin has a series resistor on 9 of 9 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 9 open source designs using the 93LC56B.
What decoupling capacitors do designs use on the 93LC56B VCC pin?
The VCC pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the 93LC56B.
What parts are used alongside the 93LC56B?
The FT2232HL, LD1117S33TR, FT231XS and ICE40HX4K-TQ144 appear in the most repositories here.
Which microcontrollers do boards using the 93LC56B use?
Most are built on FPGA (5), ESP32 (1) and STM32 (1).
How big is a typical board using the 93LC56B?
The median is 67.5 × 57 mm, and 58% are two-layer designs.
What is the most popular open source board using the 93LC56B?
By GitHub stars, Radioberry juice by pa3gsb, with 675 stars.
Can I simulate one of these boards using the 93LC56B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.