15 open source boards using the 93LC56BT-I/OT
Real designs built with the 93LC56BT-I/OT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
LCB-CCB-01 LEA Control Board
upb-lea
85 × 55 mm247 parts8LCustom license14FPGA
CPArti-FPGA-Development-Board
AAWO
100 × 100 mm393 parts4LNo license13UsbI2cSpiAdapter
hnz1102
55 × 30 mm40 parts2LNo license5FPGA
LoRaDongle
marrrk
95 × 67 mm125 parts4LNo license4FPGA
IcyBlue
Oak-Development-Technologies
50.8 × 22.8 mm73 parts4LMIT4FPGA
ICE40hxk4 dev board
smartbench
67 × 157 mm379 parts4LNo license2STM32
USB2RoMeLa Boosted
RoMeLaUCLA
18 × 31.8 mm58 parts4LMIT2FPGA
ICE40DevBoard
ddraig68k
100 × 100 mm211 parts4LNo license0Raspberry Pi
Motherboard
mikegoelzer
152.4 × 76.2 mm151 parts4LCustom license0FPGA
ECP5 BGA381 FT2232HQ FIFO
gildobjanschi
64.4 × 54.6 mm138 parts4LMIT0FPGA
VibePCB-LA
PaulBichl
98 × 64 mm103 parts6LNo license0FPGA
FPGA Board
sneakylizard123-4
50 × 70 mm81 parts4LNo license0TsuraraGB Programmer
rniwase
25.2 × 31 mm40 parts2LBSD-3-Clause16UBITz-Host z80-Host
dumaiss
84.3 × 108.4 mm48 parts4LSHL-2.10USB-JTAG-Programmer
dumaiss
31 × 35 mm24 parts4LSHL-2.10
How designs wire the 93LC56BT-I/OT
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the 93LC56BT-I/OT connects to, and the resistors, capacitors and other passives placed on it.
- The DO pin has a series resistor on 14 of 14 designs, most often 2.2 kΩ (then 2 kΩ).
- The DI pin has a series resistor on 14 of 14 designs, most often 2.2 kΩ (then 2 kΩ).
- The VCC pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 4.7 µF).
- The DO pin has a pull-up to 3.3V on 9 of 14 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| DOpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| DIpin 3 | Connected to: FT232H 21% |
|
| CLKpin 4 | Connected to: FT232H 21% |
|
| CSpin 5 | Connected to: FT232H 21% |
|
| VCCpin 6 | Connected to: 3.3V 86% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TsuraraGB Programmer by rniwase, LCB-CCB-01 LEA Control Board by upb-lea, CPArti-FPGA-Development-Board by AAWO and UsbI2cSpiAdapter by hnz1102.
The 93LC56BT-I/OT in open source designs
The gallery holds 15 open source boards using the 93LC56BT-I/OT from 14 GitHub repositories; a typical one measures about 67 × 64 mm and carries around 103 components.
87% use four copper layers or more, and 27% carry an open source license.
The most starred is TsuraraGB Programmer by rniwase.
Parts used alongside the 93LC56BT-I/OT
Microcontrollers on boards using the 93LC56BT-I/OT
What boards using the 93LC56BT-I/OT are built for
93LC56BT-I/OT: common questions
Where can I find a 93LC56BT-I/OT reference design?
Each of the 15 boards on this page is a real design using the 93LC56BT-I/OT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 93LC56BT-I/OT DO pin?
The DO pin has a series resistor on 14 of 14 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 14 open source designs using the 93LC56BT-I/OT.
What resistor goes on the 93LC56BT-I/OT DI pin?
The DI pin has a series resistor on 14 of 14 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 14 open source designs using the 93LC56BT-I/OT.
What decoupling capacitors do designs use on the 93LC56BT-I/OT VCC pin?
The VCC pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 14 open source designs using the 93LC56BT-I/OT.
What parts are used alongside the 93LC56BT-I/OT?
The USBLC6-2SC6, FT232H, FT2232HL, FT232HL and SN74LVC8T245PWR appear in the most repositories here.
Which microcontrollers do boards using the 93LC56BT-I/OT use?
Most are built on FPGA (8), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the 93LC56BT-I/OT?
The median is 67 × 64 mm, and 13% are two-layer designs.
What is the most popular open source board using the 93LC56BT-I/OT?
By GitHub stars, TsuraraGB Programmer by rniwase, with 16 stars.
Can I simulate one of these boards using the 93LC56BT-I/OT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.