30 open source boards using the ATmega328-AU
Real designs built with the ATmega328-AU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Sample Numeric Keyboard
famichu
82 × 120 mm62 parts2LCC-BY-NC-4.0465AVR/Arduino
PaperBack Converter
dqydj
76.2 × 76.2 mm75 parts2LMIT83AVR/Arduino
Mhi xy bus
iblue
91.4 × 40.6 mm66 parts2LNo license6AVR/Arduino
LoRa Dev Board RN2483
Open-Things-Network
63.5 × 43 mm35 parts2LMIT6AVR/Arduino
Counter pneumatic v1-G368
jekhor
71.1 × 132.1 mm47 parts2LNo license2AVR/Arduino
FlashProgrammer
jdisanti
61 × 38.1 mm47 parts2LApache-2.02AVR/Arduino
Delay
mschuldt
34.3 × 77.5 mm25 parts2LNo license2AVR/Arduino
Oven
hpvdt
54.6 × 108 mm20 parts2LNo license2AVR/Arduino
Timestamper
tomwimmenhove
75 × 100 mm110 parts2LGPL-3.01AVR/Arduino
Mill music
jonronen
87.1 × 51.3 mm51 parts2LNo license1AVR/Arduino
Kicad workshop
spacekookie
50 × 50 mm37 parts2LMIT1AVR/Arduino
Eurorack bastl kompas
rhinocerose
59.2 × 128.6 mm78 parts2LNo license0AVR/Arduino
Rasle
tbowmo
65 × 56 mm70 parts2LNo license0AVR/Arduino
Quark uno
protoplasma-mx
68.6 × 53.3 mm48 parts2LNo license0AVR/Arduino
AAquad
Fberbari
69.2 × 47.6 mm37 parts2LGPL-3.00AVR/Arduino
Mini data capture
GaitRehabilitation
17.5 × 29.5 mm33 parts2LApache-2.00AVR/Arduino
Pigeon
Olin-Rocketry
30 × 40 mm30 parts2LNo license0AVR/Arduino
BinaryClock
JaredWright
28.5 × 41.7 mm16 parts2LNo license0AVR/Arduino
Opensyringepump indus
PySpice-org
149.2 × 108 mm152 parts4LNo license9AVR/Arduino
Counter pneumatic v1
jekhor
91.4 × 116.2 mm38 parts2LNo license2AVR/Arduino
Run
mschuldt
34.3 × 77.5 mm22 parts2LNo license2AVR/Arduino
OHSBadge
wyolum
101.6 × 78.7 mm116 parts2LNo license1AVR/Arduino
MEP MAXI 85V-1 REV 2 Keypad
JGilcreast
209 × 97.3 mm203 parts4LNo license0AVR/Arduino
HB-UNI-Sen-CAP-MOIST
stan23
32 × 58 mm38 parts2LCC-BY-NC-4.021AVR/Arduino
While
mschuldt
34.3 × 77.5 mm22 parts2LNo license2AVR/Arduino
Repaper
wyolum
3.8 × 27.9 mm97 parts2LNo license1AVR/Arduino
Count
mschuldt
34.3 × 77.5 mm21 parts2LNo license2AVR/Arduino
P2
larsimmisch
86.4 × 45.7 mm28 parts2LNo license0AVR/Arduino
P3
larsimmisch
86.4 × 45.7 mm26 parts2LNo license0AVR/Arduino
Impulsgenerator
apxco
99 × 48.5 mm43 parts2LNo license0
How designs wire the ATmega328-AU
Read from the KiCad layouts of 24 open source designs, one per repository: what each pin of the ATmega328-AU connects to, and the resistors, capacitors and other passives placed on it.
- The XTAL1/PB6 pin has a crystal on 20 of 24 designs, most often 16 MHz (then 8 MHz).
- The XTAL2/PB7 pin has a crystal on 20 of 24 designs, most often 16 MHz (then 8 MHz).
- The RESET/PC6 pin has a pull-up to 3.3V on 19 of 24 designs, most often 10 kΩ (then 1 kΩ).
- The XTAL1/PB6 pin has a capacitor to GND on 17 of 24 designs, most often 22 pF (then 12 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 5, 21 | Connected to: GND 96% | — |
| VCCpin 4, 6 | Connected to: 3.3V 96% |
|
| XTAL1/PB6pin 7 | Connected to: Signal 92% |
|
| XTAL2/PB7pin 8 | Connected to: Signal 92% |
|
| AVCCpin 18 | Connected to: 3.3V 92% |
|
| ADC6pin 19 | Connected to: Not connected 75% · a signal 25% | — |
| AREFpin 20 | Connected to: Signal 58% · not connected 29% |
|
| ADC7pin 22 | Connected to: Not connected 71% · a signal 29% | — |
| PC4pin 27 | Connected to: A connector 38% |
|
| RESET/PC6pin 29 | Connected to: A connector 96% |
|
19 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sample Numeric Keyboard by famichu, PaperBack Converter by dqydj, HB-UNI-Sen-CAP-MOIST by stan23 and Opensyringepump indus by PySpice-org.
The ATmega328-AU in open source designs
The gallery holds 30 open source boards using the ATmega328-AU from 24 GitHub repositories; a typical one measures about 66.8 × 57 mm and carries around 41 components.
93% are two-layer designs, the rest use four layers or more, and 23% carry an open source license.
The most starred is Sample Numeric Keyboard by famichu.
Parts used alongside the ATmega328-AU
Microcontrollers on boards using the ATmega328-AU
What boards using the ATmega328-AU are built for
ATmega328-AU: common questions
Where can I find a ATmega328-AU reference design?
Each of the 30 boards on this page is a real design using the ATmega328-AU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ATmega328-AU XTAL1/PB6 pin connected?
The XTAL1/PB6 pin has a crystal on 20 of 24 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 24 open source designs using the ATmega328-AU.
How is the ATmega328-AU XTAL2/PB7 pin connected?
The XTAL2/PB7 pin has a crystal on 20 of 24 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 24 open source designs using the ATmega328-AU.
What pull-up resistor is used on the ATmega328-AU RESET/PC6 pin?
The RESET/PC6 pin has a pull-up to 3.3V on 19 of 24 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 24 open source designs using the ATmega328-AU.
What parts are used alongside the ATmega328-AU?
The FT232RL, LM358 and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the ATmega328-AU use?
Most are built on AVR/Arduino (30).
How big is a typical board using the ATmega328-AU?
The median is 66.8 × 57 mm, and 93% are two-layer designs.
What is the most popular open source board using the ATmega328-AU?
By GitHub stars, Sample Numeric Keyboard by famichu, with 465 stars.
Can I simulate one of these boards using the ATmega328-AU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.