25 open source boards using the BQ29700DSER

Real designs built with the BQ29700DSER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

25 boardsClear filters|Most starred

How designs wire the BQ29700DSER

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the BQ29700DSER connects to, and the resistors, capacitors and other passives placed on it.

  • The VSS_4 pin has a series capacitor on 12 of 13 designs, most often 100 nF.
  • The BAT_5 pin has a series capacitor on 12 of 13 designs, most often 100 nF.
  • The NC_1 pin is left unconnected on 13 of 13 designs.
  • The DOUT_3 pin has a series resistor on 9 of 13 designs, most often 5.1 MΩ (then 100 Ω).
NC_1pin 1Connected to: Not connected 100%
COUT_2pin 2Connected to: Signal 100%
  • Resistor to GND on 38% · 5.1 MΩ (5)
  • Series resistor on 31% · 5.1 MΩ (2), 100 Ω (1), 1 kΩ (1)
DOUT_3pin 3Connected to: Signal 100%
  • Series resistor on 69% · 5.1 MΩ (7), 100 Ω (1), 1 kΩ (1)
VSS_4pin 4Connected to: A connector 46%
  • Series capacitor on 92% · 100 nF (12)
  • Series resistor on 54% · 5.1 MΩ (7)
BAT_5pin 5Connected to: Signal 100%
  • Series capacitor on 92% · 100 nF (12)
  • Pull-up to VBAT on 54% · 330 Ω (7)
  • Series resistor on 38% · 330 Ω (5)
V-_6pin 6Connected to: Signal 100%
  • Resistor to GND on 69% · 2.2 kΩ (9)
  • Series resistor on 31% · 2.2 kΩ (4)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Spikeling by OpenSourceNeuro, Single cell Li-Ion protection by kajusK, Wulpus pro max by Sergio5714 and PocketLab-Card by Jebroa774.

The BQ29700DSER in open source designs

The gallery holds 25 open source boards using the BQ29700DSER from 13 GitHub repositories; a typical one measures about 44.5 × 48.3 mm and carries around 84 components.

68% use four copper layers or more, and 56% carry an open source license.

The most starred is Spikeling by OpenSourceNeuro.

Microcontrollers on boards using the BQ29700DSER

BQ29700DSER: common questions

Where can I find a BQ29700DSER reference design?

Each of the 25 boards on this page is a real design using the BQ29700DSER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the BQ29700DSER VSS_4 pin connected?

The VSS_4 pin has a series capacitor on 12 of 13 designs, most often 100 nF. Counted from the KiCad layouts of 13 open source designs using the BQ29700DSER.

How is the BQ29700DSER BAT_5 pin connected?

The BAT_5 pin has a series capacitor on 12 of 13 designs, most often 100 nF. Counted from the KiCad layouts of 13 open source designs using the BQ29700DSER.

How is the BQ29700DSER NC_1 pin connected?

The NC_1 pin is left unconnected on 13 of 13 designs. Counted from the KiCad layouts of 13 open source designs using the BQ29700DSER.

What parts are used alongside the BQ29700DSER?

The MCP73831T-2ACI/OT, W25Q128JVSIQ, BQ24074RGTR, MAX98357AETE+T and SC0914(13) appear in the most repositories here.

Which microcontrollers do boards using the BQ29700DSER use?

Most are built on RP2040/RP2350 (10), ESP32 (5), Nordic nRF (5) and AVR/Arduino (1).

How big is a typical board using the BQ29700DSER?

The median is 44.5 × 48.3 mm, and 32% are two-layer designs.

What is the most popular open source board using the BQ29700DSER?

By GitHub stars, Spikeling by OpenSourceNeuro, with 21 stars.

Can I simulate one of these boards using the BQ29700DSER before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part