18 open source boards using the CAT24C32WI-GT3
Real designs built with the CAT24C32WI-GT3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pi parport
worlickwerx
65 × 56 mm16 parts2LGPL-2.078Capes
beagleboard
111.5 × 55.8 mm91 parts2LNo license49PiStripe uHAT
pief
65 × 30 mm40 parts2LNo license5Microchip SAM
WT-220 RPi Hat and Rear IO
tuna-f1sh
173.5 × 85 mm152 parts2LGPL-3.04Pmod2rpi
fm4dd
65 × 56 mm36 parts2LCERN-OHL-1.23AVR/Arduino
UZ80
adzierzanowski
231.4 × 159.9 mm112 parts2LNo license2APMHat-4-powered
stephendade
65 × 30.5 mm57 parts2LGPL-3.01STM32
Default
RileyLeff
100 × 65 mm234 parts6LNo license0Sensor-HAT
Eniemooo
65 × 56 mm94 parts4LCC-BY-SA-4.00AVR/Arduino
Sangaboard
kitspace-test-repos
65 × 56.5 mm85 parts2LCustom license0PiPowerNew
stephendade
65 × 30 mm53 parts4LCERN-OHL-S-2.00Raspberry Pi
Canary
michael-michelotti
65 × 56 mm22 parts2LNo license0IEEE Std. 1284 HAT+
worlickwerx
65 × 56.5 mm16 parts2LGPL-2.078KakuteHAT v2
stephendade
65 × 56 mm44 parts2LGPL-3.01STM32
Default.active pre v0.2-hydration
RileyLeff
100 × 65 mm234 parts6LNo license0Raspberry Pi
PiConnectLite
stephendade
65 × 30.5 mm42 parts2LGPL-3.01STM32
Default.shipped v0.1
RileyLeff
100 × 65 mm234 parts6LNo license0Raspberry Pi
PiHat
SJSURoboticsTeam
65 × 56.5 mm12 parts4LNo license1
How designs wire the CAT24C32WI-GT3
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the CAT24C32WI-GT3 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 10 of 13 designs, most often 3.9 kΩ (then 4.7 kΩ).
- The SCL pin has a pull-up to 3.3V on 10 of 13 designs, most often 3.9 kΩ (then 4.7 kΩ).
- The A0 pin is tied to GND on 11 of 13 designs (a signal on 2).
- The A1 pin is tied to GND on 11 of 13 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 85% · a signal 15% | — |
| A1pin 2 | Connected to: GND 85% · a signal 15% | — |
| A2pin 3 | Connected to: GND 85% · a signal 15% | — |
| VSSpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: A connector 85% |
|
| SCLpin 6 | Connected to: A connector 85% |
|
| WPpin 7 | Connected to: A connector 46% |
|
| VCCpin 8 | Connected to: 3.3V 77% · a signal 23% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pi parport by worlickwerx, Capes by beagleboard, PiStripe uHAT by pief and WT-220 RPi Hat and Rear IO by tuna-f1sh.
The CAT24C32WI-GT3 in open source designs
The gallery holds 18 open source boards using the CAT24C32WI-GT3 from 13 GitHub repositories; a typical one measures about 65 × 56 mm and carries around 55 components.
67% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Pi parport by worlickwerx.
Parts used alongside the CAT24C32WI-GT3
Microcontrollers on boards using the CAT24C32WI-GT3
What boards using the CAT24C32WI-GT3 are built for
CAT24C32WI-GT3: common questions
Where can I find a CAT24C32WI-GT3 reference design?
Each of the 18 boards on this page is a real design using the CAT24C32WI-GT3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the CAT24C32WI-GT3 SDA pin?
The SDA pin has a pull-up to 3.3V on 10 of 13 designs, most often 3.9 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 13 open source designs using the CAT24C32WI-GT3.
What pull-up resistor is used on the CAT24C32WI-GT3 SCL pin?
The SCL pin has a pull-up to 3.3V on 10 of 13 designs, most often 3.9 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 13 open source designs using the CAT24C32WI-GT3.
How is the CAT24C32WI-GT3 A0 pin connected?
The A0 pin is tied to GND on 11 of 13 designs (a signal on 2). Counted from the KiCad layouts of 13 open source designs using the CAT24C32WI-GT3.
Which microcontrollers do boards using the CAT24C32WI-GT3 use?
Most are built on Raspberry Pi (3), STM32 (3), AVR/Arduino (2) and Microchip SAM (1).
How big is a typical board using the CAT24C32WI-GT3?
The median is 65 × 56 mm, and 67% are two-layer designs.
What is the most popular open source board using the CAT24C32WI-GT3?
By GitHub stars, Pi parport by worlickwerx, with 78 stars.
Can I simulate one of these boards using the CAT24C32WI-GT3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.