18 open source boards using the TPS70933DBVR

Real designs built with the TPS70933DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

18 boardsClear filters|Most starred

How designs wire the TPS70933DBVR

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the TPS70933DBVR connects to, and the resistors, capacitors and other passives placed on it.

  • The IN pin has a capacitor to GND on 9 of 12 designs, most often 1 µF (then 10 µF).
  • The EN pin is left unconnected on 10 of 12 designs (a signal on 2).
  • The OUT pin is tied to 3.3V on 8 of 12 designs (a signal on 4).
  • The IN pin has a series resistor on 5 of 12 designs, most often 172 kΩ (then 100 kΩ).
INpin 1Connected to: Signal 58% · 24V 42%
  • Capacitor to GND on 75% · 1 µF (7), 10 µF (6), 100 nF (3)
  • Series resistor on 42% · 172 kΩ (2), 100 kΩ (1), 187 kΩ (1)
GNDpin 2Connected to: GND 75% · a signal 25%
ENpin 3Connected to: Not connected 83% · a signal 17%
NCpin 4Connected to: Not connected 100%
OUTpin 5Connected to: 3.3V 67% · a signal 33%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Strip dimmer by dennisss, MYNDberry by teufelaudio, EVSE Bricklet by Tinkerforge and Esc by iamdarshg.

The TPS70933DBVR in open source designs

The gallery holds 18 open source boards using the TPS70933DBVR from 12 GitHub repositories; a typical one measures about 66.5 × 71 mm and carries around 121 components.

67% use four copper layers or more, and 50% carry an open source license.

The most starred is Strip dimmer by dennisss.

Microcontrollers on boards using the TPS70933DBVR

TPS70933DBVR: common questions

Where can I find a TPS70933DBVR reference design?

Each of the 18 boards on this page is a real design using the TPS70933DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS70933DBVR IN pin connected?

The IN pin has a capacitor to GND on 9 of 12 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 12 open source designs using the TPS70933DBVR.

How is the TPS70933DBVR EN pin connected?

The EN pin is left unconnected on 10 of 12 designs (a signal on 2). Counted from the KiCad layouts of 12 open source designs using the TPS70933DBVR.

How is the TPS70933DBVR OUT pin connected?

The OUT pin is tied to 3.3V on 8 of 12 designs (a signal on 4). Counted from the KiCad layouts of 12 open source designs using the TPS70933DBVR.

What parts are used alongside the TPS70933DBVR?

The AP2112K-3.3TRG1, STUSB4500QTR, AQH3213AX, BQ25798RQMR and CAT24C32WI-GT3 appear in the most repositories here.

Which microcontrollers do boards using the TPS70933DBVR use?

Most are built on STM32 (5), ESP32 (4), AVR/Arduino (1) and Raspberry Pi (1).

How big is a typical board using the TPS70933DBVR?

The median is 66.5 × 71 mm, and 33% are two-layer designs.

What is the most popular open source board using the TPS70933DBVR?

By GitHub stars, Strip dimmer by dennisss, with 381 stars.

Can I simulate one of these boards using the TPS70933DBVR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part