12 open source boards using the DMMT5401
Real designs built with the DMMT5401, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
PoEPi hardware
julien8
93.8 × 30 mm81 parts2LNo license46Raspberry Pi
Slushengine modelx
Roboteurs
261 × 100 mm205 parts2LCustom license8Raspberry Pi
BlueBerry-Zero
idlehandsdev
65 × 30 mm43 parts2LGPL-2.05PiStripe uHAT
pief
65 × 30 mm40 parts2LNo license5STM32
Cognicity floodsensor
smart-facility
66 × 57 mm57 parts2LGPL-3.04Raspberry Pi
Mearm pi hat
mimeindustries
65 × 56.5 mm24 parts2LNo license4Raspberry Pi
DronPi
radioelf
71.8 × 50.9 mm135 parts2LNo license1Warp energy manager bricklet
Tinkerforge
68 × 87 mm100 parts4LNo license1Rpi power hat
KPI-Rover
65 × 56.5 mm38 parts2LNo license1AVR/Arduino
PiUPS
Blake-Robotics
65 × 56.5 mm82 parts2LGPL-2.00Raspberry Pi
Pihat
UMONS-GFA
65 × 56.5 mm33 parts2LCERN-OHL-1.20STM32
Pi3 hat
Jayanth-M0625
56.5 × 65 mm135 parts4LNo license0
How designs wire the DMMT5401
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the DMMT5401 connects to, and the resistors, capacitors and other passives placed on it.
- The C1 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ).
- The B1 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ).
- The B2 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ).
- The C2 pin has a resistor to GND on 12 of 12 designs, most often 47 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| C1pin 1 | Connected to: Signal 100% |
|
| B1pin 2 | Connected to: Signal 100% |
|
| B2pin 3 | Connected to: Signal 100% |
|
| C2pin 4 | Connected to: Signal 100% |
|
| E2pin 5 | Connected to: 5V 67% · a signal 33% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PoEPi hardware by julien8, Slushengine modelx by Roboteurs, BlueBerry-Zero by idlehandsdev and PiStripe uHAT by pief.
The DMMT5401 in open source designs
The gallery holds 12 open source boards using the DMMT5401 from 12 GitHub repositories; a typical one measures about 65 × 56.5 mm and carries around 69 components.
83% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is PoEPi hardware by julien8.
Parts used alongside the DMMT5401
Microcontrollers on boards using the DMMT5401
What boards using the DMMT5401 are built for
DMMT5401: common questions
Where can I find a DMMT5401 reference design?
Each of the 12 boards on this page is a real design using the DMMT5401. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the DMMT5401 C1 pin?
The C1 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 12 open source designs using the DMMT5401.
What resistor goes on the DMMT5401 B1 pin?
The B1 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 12 open source designs using the DMMT5401.
What resistor goes on the DMMT5401 B2 pin?
The B2 pin has a resistor to GND on 12 of 12 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 12 open source designs using the DMMT5401.
What parts are used alongside the DMMT5401?
The LM1117IMPX-ADJ, FDC5614P and LM3489 appear in the most repositories here.
Which microcontrollers do boards using the DMMT5401 use?
Most are built on Raspberry Pi (6), STM32 (2) and AVR/Arduino (1).
How big is a typical board using the DMMT5401?
The median is 65 × 56.5 mm, and 83% are two-layer designs.
What is the most popular open source board using the DMMT5401?
By GitHub stars, PoEPi hardware by julien8, with 46 stars.
Can I simulate one of these boards using the DMMT5401 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.