18 open source boards using the DRV8837
Real designs built with the DRV8837, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Mobo
opulo-inc
51.6 × 89 mm57 parts2LCC-BY-SA-4.0193STM32
Temperature logger
Jana-Marie
106 × 50 mm151 parts4LCERN-OHL-S-2.068ESP32
PrettySmallRobot
wattnotions
26 × 29 mm51 parts4LNo license23STM32
Longboi
KungfuPancake
358 × 40 mm285 parts4LApache-2.07STM32
Maslab
maslab-5
99.1 × 99.1 mm317 parts4LNo license4NeoBoard
alvaroferran
40 × 40 mm73 parts2LNo license3Microchip SAM
Mini rocket flight controller
AmitBarman99
73.7 × 49.3 mm108 parts4LNo license2STM32
Floppy-Ant-Controller
FloppyO1
65 × 60 mm53 parts2LCERN-OHL-S-2.02Esp32-thermostat
waerhert
124 × 53 mm13 parts2LMIT1Main 4.3 old
hughminhphan
133.1 × 97.6 mm144 parts4LNo license0ESP32
Kabot
kabot-io
89 × 92.5 mm137 parts2LCC-BY-NC-4.00STM32
IbScaleFeederLite
ibScale
51.6 × 89 mm74 parts4LCERN-OHL-S-2.00PCB-Toilet-Water
VozarX
54.6 × 26.7 mm39 parts2LNo license0AVR/Arduino
QuectoDrive
edatki
15.2 × 12.1 mm14 parts2LNo license0Power subsystem
Dichochi
30.6 × 23.6 mm18 parts2LNo license0EEE3088 Power
CScheepers1504
22.4 × 22 mm13 parts2LGPL-3.00Motor Driver
kabot-io
15.3 × 6.6 mm11 parts2LCC-BY-NC-4.00RISC-V
Osc sg90-v006
OpenServoCore
20.6 × 9.6 mm26 parts4LApache-2.034
How designs wire the DRV8837
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the DRV8837 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 16 of 17 designs, most often 100 nF (then 1 µF).
- The VM pin has a decoupling capacitor on 15 of 17 designs, most often 100 nF (then 22 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VMpin 1 | Connected to: BATT 82% · a signal 18% |
|
| GNDpin 4, 9 | Connected to: GND 91% | — |
| SLEEPpin 7 | Connected to: The microcontroller 29%, DRV8837 24% · 3.3V 35% |
|
| VCCpin 8 | Connected to: 3.3V 94% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mobo by opulo-inc, Temperature logger by Jana-Marie, Osc sg90-v006 by OpenServoCore and PrettySmallRobot by wattnotions.
The DRV8837 in open source designs
The gallery holds 18 open source boards using the DRV8837 from 17 GitHub repositories; a typical one measures about 53.1 × 44.6 mm and carries around 55 components.
56% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Mobo by opulo-inc.
Parts used alongside the DRV8837
Microcontrollers on boards using the DRV8837
What boards using the DRV8837 are built for
DRV8837: common questions
Where can I find a DRV8837 reference design?
Each of the 18 boards on this page is a real design using the DRV8837. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DRV8837 VCC pin?
The VCC pin has a decoupling capacitor on 16 of 17 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 17 open source designs using the DRV8837.
What decoupling capacitors do designs use on the DRV8837 VM pin?
The VM pin has a decoupling capacitor on 15 of 17 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 17 open source designs using the DRV8837.
What parts are used alongside the DRV8837?
The AMS1117-3.3, AP1117-33 and STM32F031C6Tx appear in the most repositories here.
Which microcontrollers do boards using the DRV8837 use?
Most are built on STM32 (6), ESP32 (2), AVR/Arduino (1) and RISC-V (1).
How big is a typical board using the DRV8837?
The median is 53.1 × 44.6 mm, and 56% are two-layer designs.
What is the most popular open source board using the DRV8837?
By GitHub stars, Mobo by opulo-inc, with 193 stars.
Can I simulate one of these boards using the DRV8837 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.