13 open source boards using the FSUSB42UMX

Real designs built with the FSUSB42UMX, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the FSUSB42UMX

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the FSUSB42UMX connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 11 of 12 designs, most often 100 nF (then 1 µF).
  • The SEL pin has a resistor to GND on 6 of 12 designs, most often 22 kΩ (then 10 kΩ).
  • The SEL pin has a series resistor on 5 of 12 designs, most often 10 kΩ (then 6.04 kΩ).
D+pin 1Connected to: A connector 42%
  • Series resistor on 33% · 22 Ω (2), 10 kΩ (1), 0 Ω (1)
D-pin 2Connected to: A connector 42%
  • Series resistor on 33% · 22 Ω (2), 220 Ω (1), 0 Ω (1)
GNDpin 3Connected to: GND 92%
OEpin 8Connected to: GND 58% · a signal 42%
  • Resistor to GND on 33% · 10 kΩ (3)
VCCpin 9Connected to: 3.3V 83% · a signal 17%
  • Decoupling capacitor on 92% · 100 nF (11), 1 µF (1)
SELpin 10Connected to: Signal 92%
  • Resistor to GND on 50% · 22 kΩ (3), 10 kΩ (2)
  • Series resistor on 42% · 10 kΩ (2), 6.04 kΩ (1), 47 kΩ (1)
  • Pull-up to 3.3V on 33% · 10 kΩ (2), 51 kΩ (1), 100 kΩ (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Uno by lukasloetkolben, RPI CMx Carrier by lecejeff, ReDIP-64 by daglem and Moducard cm5-module by Dominik-Workshop.

The FSUSB42UMX in open source designs

The gallery holds 13 open source boards using the FSUSB42UMX from 12 GitHub repositories; a typical one measures about 100 × 74.1 mm and carries around 137 components.

62% use four copper layers or more, and 69% carry an open source license.

The most starred is Uno by lukasloetkolben.

Parts used alongside the FSUSB42UMX

Microcontrollers on boards using the FSUSB42UMX

FSUSB42UMX: common questions

Where can I find a FSUSB42UMX reference design?

Each of the 13 boards on this page is a real design using the FSUSB42UMX. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the FSUSB42UMX VCC pin?

The VCC pin has a decoupling capacitor on 11 of 12 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 12 open source designs using the FSUSB42UMX.

What resistor goes on the FSUSB42UMX SEL pin?

The SEL pin has a resistor to GND on 6 of 12 designs, most often 22 kΩ (then 10 kΩ). Counted from the KiCad layouts of 12 open source designs using the FSUSB42UMX.

What parts are used alongside the FSUSB42UMX?

The CH334P, AMS1117-3.3, STM32F103CBTx and TJA1044GTK/3Z appear in the most repositories here.

Which microcontrollers do boards using the FSUSB42UMX use?

Most are built on ESP32 (4), STM32 (4), FPGA (1) and PIC (1).

How big is a typical board using the FSUSB42UMX?

The median is 100 × 74.1 mm, and 38% are two-layer designs.

What is the most popular open source board using the FSUSB42UMX?

By GitHub stars, Uno by lukasloetkolben, with 92 stars.

Can I simulate one of these boards using the FSUSB42UMX before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part