17 open source boards using the CH334P

Real designs built with the CH334P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the CH334P

Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the CH334P connects to, and the resistors, capacitors and other passives placed on it.

  • The VDD33 pin has a capacitor to GND on 13 of 14 designs, most often 100 nF (then 10 µF).
  • The V5 pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 1 µF).
  • The RESET/CDP_13 pin is left unconnected on 13 of 14 designs.
  • The XO pin has a crystal on 10 of 14 designs, most often 12 MHz.
XOpin 1Connected to: Signal 71% · not connected 29%
  • Crystal on 71% · 12 MHz (7)
XIpin 2Connected to: Signal 71% · not connected 21%
  • Crystal on 71% · 12 MHz (7)
DM2pin 7Connected to: A connector 21%
  • Series resistor on 36% · 22 Ω (4)
DP2pin 8Connected to: A connector 21%
  • Series resistor on 36% · 22 Ω (4)
RESET/CDP_13pin 13Connected to: Not connected 93%
PGANGpin 14Connected to: Not connected 71% · a signal 29%
V5pin 15Connected to: 5V 100%
  • Decoupling capacitor on 86% · 100 nF (8), 1 µF (5), 10 µF (3)
VDD33pin 16Connected to: Signal 64% · 3.3V 36%
  • Capacitor to GND on 93% · 100 nF (14), 10 µF (6), 4.7 µF (1)
GNDpin 17Connected to: GND 93%

8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiSTle - Icepi-Zero Carrier by MiSTle-Dev, Moducard cm5-module by Dominik-Workshop, Skibidi usb c hub by tobycm and Bottom board palmtop by ZeroPhone.

The CH334P in open source designs

The gallery holds 17 open source boards using the CH334P from 14 GitHub repositories; a typical one measures about 90 × 67 mm and carries around 119 components.

65% are two-layer designs, the rest use four layers or more, and 59% carry an open source license.

The most starred is MiSTle - GW3A LV20 LQ144 Development Board by MiSTle-Dev.

Microcontrollers on boards using the CH334P

CH334P: common questions

Where can I find a CH334P reference design?

Each of the 17 boards on this page is a real design using the CH334P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the CH334P VDD33 pin connected?

The VDD33 pin has a capacitor to GND on 13 of 14 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 14 open source designs using the CH334P.

What decoupling capacitors do designs use on the CH334P V5 pin?

The V5 pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 14 open source designs using the CH334P.

How is the CH334P RESET/CDP_13 pin connected?

The RESET/CDP_13 pin is left unconnected on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the CH334P.

What parts are used alongside the CH334P?

The USBLC6-2SC6, FSUSB42UMX, STM32F103CBTx, TJA1044GTK/3Z and MT48LC16M16A2TG appear in the most repositories here.

Which microcontrollers do boards using the CH334P use?

Most are built on STM32 (7), RP2040/RP2350 (3) and ESP32 (1).

How big is a typical board using the CH334P?

The median is 90 × 67 mm, and 65% are two-layer designs.

What is the most popular open source board using the CH334P?

By GitHub stars, MiSTle - GW3A LV20 LQ144 Development Board by MiSTle-Dev, with 22 stars.

Can I simulate one of these boards using the CH334P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part