13 open source boards using the FT2232D
Real designs built with the FT2232D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Karnix ASB-254
Fabmicro-LLC
85 × 56 mm364 parts6LCustom license19STM32
FHNW-Pro4E-FS19T8-3DPrinterBoard-STM32
mnemocron
158 × 95 mm258 parts4LGPL-3.016STM32
Hdmilight v3
esar
100 × 100 mm249 parts2LGPL-2.08FrequencyCounter
LUMERIIX
130 × 90 mm125 parts4LNo license5ModBus-RJ45-Breakout-2
the78mole
87 × 68 mm116 parts2LTAPR-OHL-1.01Raspberry Pi
Piweather
pluggee
65 × 64 mm58 parts4LMIT1ESP32
Senzori iradiere
cs-pub-ro
103 × 126 mm328 parts4LNo license0Interrruptus
parceval
100 × 100 mm42 parts4LBSD-3-Clause0USB CopyNES
famicomical
88.8 × 114.5 mm34 parts2LNo license0TsuraraGB Programmer
rniwase
25.2 × 31 mm40 parts2LBSD-3-Clause16Supercapacitors balancing
cs-pub-ro
21 × 92 mm30 parts2LNo license0Temperature sesor
cs-pub-ro
13.5 × 24.7 mm8 parts2LNo license0FPGA
O2 breakout
m-okada
95 × 72 mm101 parts2LNo license3
How designs wire the FT2232D
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the FT2232D connects to, and the resistors, capacitors and other passives placed on it.
- The RSTOUT pin has a series resistor on 11 of 11 designs, most often 1.5 kΩ (then 2.2 kΩ).
- The 3V3OUT pin has a capacitor to GND on 11 of 11 designs, most often 100 nF (then 33 nF).
- The USBDP pin has a series resistor on 11 of 11 designs, most often 1.5 kΩ (then 27 Ω).
- The USBDM pin has a series resistor on 10 of 11 designs, most often 27 Ω (then 22 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| EEDATApin 2 | Connected to: Signal 91% |
|
| VCCpin 3, 42 | Connected to: 5V 91% |
|
| RESETpin 4 | Connected to: Signal 55% · 5V 45% |
|
| RSTOUTpin 5 | Connected to: Signal 100% |
|
| 3V3OUTpin 6 | Connected to: Signal 91% |
|
| USBDPpin 7 | Connected to: Signal 100% |
|
| USBDMpin 8 | Connected to: Signal 100% |
|
| GNDpin 9, 18, 25, 34 | Connected to: GND 100% | — |
| ACBUS3pin 11 | Connected to: Not connected 64% · a signal 36% | — |
| ACBUS2pin 12 | Connected to: Not connected 64% · a signal 36% | — |
| ACBUS1pin 13 | Connected to: Not connected 82% · a signal 18% | — |
| VCCIOApin 14 | Connected to: 3.3V 73% · a signal 27% |
|
| ACBUS0pin 15 | Connected to: Not connected 73% · a signal 27% | — |
| ADBUS7pin 16 | Connected to: Not connected 82% · a signal 18% | — |
| ADBUS6pin 17 | Connected to: Not connected 91% | — |
| ADBUS5pin 19 | Connected to: Not connected 91% | — |
| ADBUS4pin 20 | Connected to: Not connected 82% · a signal 18% | — |
| ADBUS1pin 23 | Connected to: A connector 27% |
|
| BCBUS3pin 27 | Connected to: Signal 55% · not connected 45% |
|
| BCBUS2pin 28 | Connected to: Signal 55% · not connected 45% |
|
| BCBUS1pin 29 | Connected to: Not connected 91% | — |
| BCBUS0pin 30 | Connected to: Not connected 73% · a signal 27% | — |
| VCCIOBpin 31 | Connected to: 3.3V 82% · a signal 18% |
|
| BDBUS7pin 32 | Connected to: Not connected 91% | — |
| BDBUS6pin 33 | Connected to: Not connected 82% | — |
| BDBUS5pin 35 | Connected to: Not connected 91% | — |
| BDBUS4pin 36 | Connected to: Not connected 64% · a signal 36% | — |
| BDBUS3pin 37 | Connected to: Not connected 82% · a signal 18% | — |
| PWRENpin 41 | Connected to: Not connected 73% · a signal 27% | — |
| XTINpin 43 | Connected to: Signal 100% |
|
| XTOUTpin 44 | Connected to: Signal 82% · not connected 18% |
|
| AGNDpin 45 | Connected to: GND 100% | — |
| AVCCpin 46 | Connected to: Signal 82% · AVCC 18% |
|
| TESTpin 47 | Connected to: GND 100% | — |
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Karnix ASB-254 by Fabmicro-LLC, FHNW-Pro4E-FS19T8-3DPrinterBoard-STM32 by mnemocron, TsuraraGB Programmer by rniwase and Hdmilight v3 by esar.
The FT2232D in open source designs
The gallery holds 13 open source boards using the FT2232D from 11 GitHub repositories; a typical one measures about 88.8 × 90 mm and carries around 101 components.
54% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is Karnix ASB-254 by Fabmicro-LLC.
Parts used alongside the FT2232D
Microcontrollers on boards using the FT2232D
What boards using the FT2232D are built for
FT2232D: common questions
Where can I find a FT2232D reference design?
Each of the 13 boards on this page is a real design using the FT2232D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the FT2232D RSTOUT pin?
The RSTOUT pin has a series resistor on 11 of 11 designs, most often 1.5 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 11 open source designs using the FT2232D.
How is the FT2232D 3V3OUT pin connected?
The 3V3OUT pin has a capacitor to GND on 11 of 11 designs, most often 100 nF (then 33 nF). Counted from the KiCad layouts of 11 open source designs using the FT2232D.
What resistor goes on the FT2232D USBDP pin?
The USBDP pin has a series resistor on 11 of 11 designs, most often 1.5 kΩ (then 27 Ω). Counted from the KiCad layouts of 11 open source designs using the FT2232D.
What parts are used alongside the FT2232D?
The 93CxxB, 93LC46B, ESP32-WROOM-32 and MAX40200AUK appear in the most repositories here.
Which microcontrollers do boards using the FT2232D use?
Most are built on FPGA (2), STM32 (2), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the FT2232D?
The median is 88.8 × 90 mm, and 54% are two-layer designs.
What is the most popular open source board using the FT2232D?
By GitHub stars, Karnix ASB-254 by Fabmicro-LLC, with 19 stars.
Can I simulate one of these boards using the FT2232D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.