16 open source boards using the LTV-847
Real designs built with the LTV-847, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
MPCNC-Nano-Estlcam-Shield
tnn85
160 × 100 mm92 parts2LCustom license70ESP8266
Atu100wifi
ftl
83.8 × 120.7 mm23 parts2LMIT28T4-MFA
gmoccapy
63 × 80 mm41 parts2LNo license7Backup
411568
320 × 81.3 mm98 parts2LMIT3Int board
dglcinc
59 × 85 mm25 parts2LMIT2AVR/Arduino
Vigor22 C
jstrebel
122.9 × 70 mm98 parts2LNo license1AVR/Arduino
ArduPLC
Reiken3099
101.6 × 101.6 mm86 parts2LCC0-1.01AVR/Arduino
Rotator-Controller
jft-t
100 × 100 mm55 parts2LGPL-3.01ESP32
Ekspander 100x i2c
kanaboid
500 × 108.8 mm264 parts4LNo license0AVR/Arduino
All band amp-April-2026
satspares
139.5 × 101 mm142 parts4LMIT0Raspberry Pi
Bottom HAT Train Control Circuit
PetervanderMeij
85.6 × 56.5 mm57 parts2LNo license0Fm radio panel
411568
320 × 83.8 mm98 parts2LMIT3Level shifter
SBC-Collaboration
49.3 × 48.3 mm18 parts2LNo license1Control Panel Motherboard
Enthusela
91.3 × 74.7 mm43 parts2LNo license0Control Panel Motherboard top RF IDC
Enthusela
98.8 × 84.1 mm42 parts2LNo license0ControlPanel RF Breakout
Enthusela
73.7 × 60.5 mm24 parts2LNo license0
How designs wire the LTV-847
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the LTV-847 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω).
- Pin 3 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω).
- Pin 5 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 23% |
|
| Pin 3 | Connected to: A connector 23% |
|
| Pin 5 | Connected to: A connector 31% |
|
| Pin 7 | Connected to: A connector 31% · not connected 15% |
|
| Pin 9 | Connected to: GND 46% · not connected 15% · a signal 38% |
|
| Pin 11 | Connected to: A connector 23% · GND 46% |
|
| Pin 13 | Connected to: A connector 23% · GND 46% |
|
| Pin 15 | Connected to: A connector 23% · GND 46% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MPCNC-Nano-Estlcam-Shield by tnn85, Atu100wifi by ftl, T4-MFA by gmoccapy and Backup by 411568.
The LTV-847 in open source designs
The gallery holds 16 open source boards using the LTV-847 from 13 GitHub repositories; a typical one measures about 99.4 × 83.9 mm and carries around 56 components.
88% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is MPCNC-Nano-Estlcam-Shield by tnn85.
Parts used alongside the LTV-847
Microcontrollers on boards using the LTV-847
What boards using the LTV-847 are built for
LTV-847: common questions
Where can I find a LTV-847 reference design?
Each of the 16 boards on this page is a real design using the LTV-847. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LTV-847 pin 1?
Pin 1 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 13 open source designs using the LTV-847.
What resistor goes on the LTV-847 pin 3?
Pin 3 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 13 open source designs using the LTV-847.
What resistor goes on the LTV-847 pin 5?
Pin 5 has a series resistor on 8 of 13 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 13 open source designs using the LTV-847.
What parts are used alongside the LTV-847?
The Arduino_Nano_v3.x, LM358 and MCP23017_SP appear in the most repositories here.
Which microcontrollers do boards using the LTV-847 use?
Most are built on AVR/Arduino (5), ESP32 (1), ESP8266 (1) and Raspberry Pi (1).
How big is a typical board using the LTV-847?
The median is 99.4 × 83.9 mm, and 88% are two-layer designs.
What is the most popular open source board using the LTV-847?
By GitHub stars, MPCNC-Nano-Estlcam-Shield by tnn85, with 70 stars.
Can I simulate one of these boards using the LTV-847 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.