28 open source boards using the MCP2515

Real designs built with the MCP2515, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

28 boardsClear filters|Most starred

How designs wire the MCP2515

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MCP2515 connects to, and the resistors, capacitors and other passives placed on it.

  • The CLKOUT/SOF pin is left unconnected on 8 of 9 designs.
  • The TX0RTS pin is left unconnected on 8 of 9 designs.
  • The TX1RTS pin is left unconnected on 8 of 9 designs.
  • The OSC2 pin has a capacitor to GND on 6 of 8 designs, most often 22 pF (then 18 pF).
CLKOUT/SOFpin 3Connected to: Not connected 89%
TX0RTSpin 4Connected to: Not connected 89%
TX1RTSpin 5Connected to: Not connected 89%
TX2RTSpin 6Connected to: Not connected 78% · a signal 22%
OSC2pin 7Connected to: Signal 75% · not connected 25%
  • Capacitor to GND on 75% · 22 pF (5), 18 pF (1)
  • Crystal on 63% · 16 MHz (3), 8 MHz (1)
OSC1pin 8Connected to: Signal 88%
  • Crystal on 63% · 16 MHz (2), 8 MHz (1), 20 MHz (1)
  • Capacitor to GND on 63% · 22 pF (4), 18 pF (1)
VSSpin 9Connected to: GND 88%
RX1BFpin 10Connected to: Not connected 88%
RX0BFpin 11Connected to: Not connected 75% · a signal 25%
RESETpin 17Connected to: Signal 75%
  • Pull-up to 3.3V on 50% · 10 kΩ (3), 4.7 kΩ (1)
VDDpin 18Connected to: 3.3V 75% · a signal 25%
  • Decoupling capacitor on 75% · 100 nF (8), 10 µF (1)

7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RPi-MCP2515 by GBert, ESC Drivetrain V1 by mark-belbin, FullInterlockingPlantCAN by RobertPHeller and PiMainboard by UofSSpaceTeam.

The MCP2515 in open source designs

The gallery holds 28 open source boards using the MCP2515 from 10 GitHub repositories; a typical one measures about 159.1 × 100 mm and carries around 152 components.

52% use four copper layers or more, and 29% carry an open source license.

The most starred is RPi-MCP2515 by GBert.

Microcontrollers on boards using the MCP2515

MCP2515: common questions

Where can I find a MCP2515 reference design?

Each of the 28 boards on this page is a real design using the MCP2515. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP2515 CLKOUT/SOF pin connected?

The CLKOUT/SOF pin is left unconnected on 8 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the MCP2515.

How is the MCP2515 TX0RTS pin connected?

The TX0RTS pin is left unconnected on 8 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the MCP2515.

How is the MCP2515 TX1RTS pin connected?

The TX1RTS pin is left unconnected on 8 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the MCP2515.

What parts are used alongside the MCP2515?

The MCP2562, MCP2551, MPU-9250, PCA9306 and SN65HVD230 appear in the most repositories here.

Which microcontrollers do boards using the MCP2515 use?

Most are built on AVR/Arduino (16), Raspberry Pi (2) and ESP32 (1).

How big is a typical board using the MCP2515?

The median is 159.1 × 100 mm, and 48% are two-layer designs.

What is the most popular open source board using the MCP2515?

By GitHub stars, RPi-MCP2515 by GBert, with 99 stars.

Can I simulate one of these boards using the MCP2515 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part