40 open source boards using the PCA9306
Real designs built with the PCA9306, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
- schematic only · 63 partsNXP
Dodohand
dodohand
63 partsGPL-3.0115 FPGA
Zynq
juliancoy
120 × 60 mm295 partsMIT751 Distribution Board
basicallysource
130 × 120 mm179 parts2LNo license38Pauline
jfdelnero
77.1 × 63.8 mm152 parts4LNo license25STM32
Isoblue
oats-center
115 × 78 mm114 parts4LMIT25ESP32
Paperflux
albanpetit
33.5 × 50 mm43 parts4LNo license16ESP32
SparkPNT GNSSDO Plus
sparkfun
151.9 × 101.6 mm347 parts4LMIT696boards robomezzi
mwelling
85 × 54 mm112 parts4LCC-BY-SA-4.06EdisonPC104
spel-uchile
96 × 92 mm24 parts2LNo license6- schematic only · 170 parts
Yatagarasu red
DCoJA
170 partsCC-BY-SA-4.05 Si468x
NightLaneOrg
22 × 30 mm51 parts4LGPL-3.04Si468x
NightLaneOrg
22 × 30 mm54 parts4LGPL-3.03STM32
Flight computer
cuspaceflight
80 × 80 mm114 parts4LNo license2ESP32
NX-ISD
Ghost3379
77 × 48.6 mm108 parts4LGPL-3.02AVR/Arduino
Power Supply
adsehgal
100 × 50 mm94 parts2LNo license2Cluster2HDMI
vkar9898
128 × 55 mm94 parts4LMIT2HxCFloppyEmulator
johna23-lab
77.1 × 63.8 mm152 parts4LNo license1Hxcfloppyemu
BakedSnake
77.1 × 63.8 mm152 parts4LNo license1Raspberry Pi
DronPi
radioelf
71.8 × 50.9 mm135 parts2LNo license1ESP32
PowerControlBoard
takaki-maeda-99
100 × 85 mm108 parts4LNo license1ImpedanceP2
wenkeli
98 × 79.6 mm69 parts2LNo license1AVR/Arduino
NLog 9DoF
kentN
45 × 45 mm51 parts2LMIT1ESP32
Quickstep controller
Govish
192.5 × 165 mm235 parts2LNo license0STM32
STDC
SebastianThomas
38 × 48 mm120 parts4LNo license0NXP
Mainframe led tube
lordiii
99.1 × 116.8 mm79 parts2LGPL-3.00PIC
EkoPuszka
media3-0
72.4 × 45.7 mm75 parts2LMIT0AVR/Arduino
ElaraGNSSMKRShield
generationmake
61.5 × 25 mm37 parts2LCustom license0AVR/Arduino
Mini data capture
GaitRehabilitation
17.5 × 29.5 mm33 parts2LApache-2.00QWIIC-SWITCH-PROJECT
Harshad-vali
30 × 24 mm19 parts2LNo license0- schematic only · 61 partsESP32
JWatch
JujuXu
61 partsNo license0 - schematic only · 47 partsESP32
Smartwatch-HackClub-Fallen-Project
aAhmer1677
47 partsMIT0 - schematic only · 29 partsSTM32
Better erc
romixlab
29 partsNo license0 ESP32OlcbIO Servo Extension Board
atanisoft
61 × 62 mm33 parts2LNo license12ESP32
SparkPNT GNSSDO Plus panelized
sparkfun
165.6 × 125.5 mm347 parts4LMIT6BREAD Loaf
FHafting
35.4 × 50.7 mm32 parts2LNo license5STM32
C6v1.0
parsa-novin
127 × 127 mm140 parts4LNo license2
How designs wire the PCA9306
Read from the KiCad layouts of 31 open source designs, one per repository: what each pin of the PCA9306 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL1 pin has a pull-up to 3.3V on 24 of 31 designs, most often 2.2 kΩ (then 4.7 kΩ).
- The SDA1 pin has a pull-up to 3.3V on 24 of 31 designs, most often 2.2 kΩ (then 4.7 kΩ).
- The EN pin has a pull-up to 5V on 24 of 31 designs, most often 200 kΩ (then 0 Ω).
- The VREF2 pin has a pull-up to 5V on 23 of 31 designs, most often 200 kΩ (then 0 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 97% | — |
| VREF1pin 2 | Connected to: 3.3V 90% |
|
| SCL1pin 3 | Connected to: A connector 45%, the microcontroller 23% |
|
| SDA1pin 4 | Connected to: A connector 45% |
|
| SDA2pin 5 | Connected to: A connector 48% |
|
| SCL2pin 6 | Connected to: A connector 52% |
|
| VREF2pin 7 | Connected to: Signal 84% · 3.3V 16% |
|
| ENpin 8 | Connected to: Signal 90% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ZynqPCB by juliancoy, 1 Distribution Board by basicallysource, Pauline by jfdelnero and Isoblue by oats-center.
The PCA9306 in open source designs
The gallery holds 40 open source boards using the PCA9306 from 36 GitHub repositories; a typical one measures about 80 × 62 mm and carries around 101 components.
56% use four copper layers or more, and 45% carry an open source license.
The most starred is Dodohand by dodohand.
Parts used alongside the PCA9306
Microcontrollers on boards using the PCA9306
What boards using the PCA9306 are built for
PCA9306: common questions
Where can I find a PCA9306 reference design?
Each of the 40 boards on this page is a real design using the PCA9306. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCA9306 SCL1 pin?
The SCL1 pin has a pull-up to 3.3V on 24 of 31 designs, most often 2.2 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 31 open source designs using the PCA9306.
What pull-up resistor is used on the PCA9306 SDA1 pin?
The SDA1 pin has a pull-up to 3.3V on 24 of 31 designs, most often 2.2 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 31 open source designs using the PCA9306.
What pull-up resistor is used on the PCA9306 EN pin?
The EN pin has a pull-up to 5V on 24 of 31 designs, most often 200 kΩ (then 0 Ω). Counted from the KiCad layouts of 31 open source designs using the PCA9306.
What parts are used alongside the PCA9306?
The MPU-9250, 74LCX125MX, MC74LVX14DR2G, SN74LS06D and 74HC245 appear in the most repositories here.
Which microcontrollers do boards using the PCA9306 use?
Most are built on ESP32 (11), STM32 (5), AVR/Arduino (4) and NXP (2).
How big is a typical board using the PCA9306?
The median is 80 × 62 mm, and 44% are two-layer designs.
What is the most popular open source board using the PCA9306?
By GitHub stars, Dodohand by dodohand, with 115 stars.
Can I simulate one of these boards using the PCA9306 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.