14 open source boards using the MCP6002-I/P
Real designs built with the MCP6002-I/P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FunBox
GuitarML
59.7 × 67.5 mm63 parts2LMIT286- schematic only · 15 partsAVR/Arduino
Bcm3000
aschet
15 parts2LMIT2 PCBRev2
MilesMayhew
213.4 × 128.3 mm63 parts2LNo license1ESP32
Microgrid-Home-Energy-Monitor
dish-glitch
130.2 × 72.9 mm36 parts2LMIT1ESP32
Photodiode lab
fborello-lambda
100 × 100 mm22 parts2LNo license1Szscreen - CONSOLE LAB 160 x 120 / ENGINEERING PROTOTYPE
gmaxdragon
160 × 120 mm156 parts2LNo license0Effect pedal
Ahreo
104.8 × 97.8 mm85 parts2LNo license0AVR/Arduino
Nano delay pedal
barlasardic
55.9 × 88.9 mm57 parts2LMIT0ESP32
PiezotesterV2.1
JakubJasiejko
119.3 × 97.4 mm49 parts2LMIT0Audio sync circuit
melizalab
45.5 × 30.5 mm13 parts2LNo license0- schematic only · 22 parts
Lm5116-ccv buck
QDarkRex
22 partsMIT0 !!UNTESTED!!
niektb
50.5 × 128.5 mm124 parts2LCC-BY-SA-4.034Capstone
MilesMayhew
232.4 × 172.7 mm55 parts2LNo license1ESP32
Urzadzenie badawcze V2
JakubJasiejko
91.4 × 71.7 mm17 parts2LMIT0
How designs wire the MCP6002-I/P
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the MCP6002-I/P connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 10 of 10 designs.
- The VOUTA pin has a series resistor on 7 of 10 designs, most often 33 kΩ (then 10 kΩ).
- The + pins have a resistor to GND on 7 of 10 designs, most often 10 kΩ (then 4.7 kΩ).
- The - pins have a series resistor on 6 of 10 designs, most often 100 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTApin 1 | Connected to: A connector 20% |
|
| -pin 2, 6 | Connected to: Signal 90% |
|
| +pin 3, 5 | Connected to: Signal 75% |
|
| V-pin 4 | Connected to: GND 100% | — |
| VOUTBpin 7 | Connected to: Signal 80% |
|
| V+pin 8 | Connected to: 5V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FunBox by GuitarML, !!UNTESTED!! by niektb, Microgrid-Home-Energy-Monitor by dish-glitch and Photodiode lab by fborello-lambda.
The MCP6002-I/P in open source designs
The gallery holds 14 open source boards using the MCP6002-I/P from 12 GitHub repositories; a typical one measures about 102.4 × 97.6 mm and carries around 52 components.
100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is FunBox by GuitarML.
Parts used alongside the MCP6002-I/P
Microcontrollers on boards using the MCP6002-I/P
What boards using the MCP6002-I/P are built for
MCP6002-I/P: common questions
Where can I find a MCP6002-I/P reference design?
Each of the 14 boards on this page is a real design using the MCP6002-I/P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP6002-I/P V- pin connected?
The V- pin is tied to GND on 10 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the MCP6002-I/P.
What resistor goes on the MCP6002-I/P VOUTA pin?
The VOUTA pin has a series resistor on 7 of 10 designs, most often 33 kΩ (then 10 kΩ). Counted from the KiCad layouts of 10 open source designs using the MCP6002-I/P.
What resistor goes on the MCP6002-I/P + pin?
The + pins have a resistor to GND on 7 of 10 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 10 open source designs using the MCP6002-I/P.
What parts are used alongside the MCP6002-I/P?
The LM7805_TO220, SN74AHC14N and TL072CP appear in the most repositories here.
Which microcontrollers do boards using the MCP6002-I/P use?
Most are built on ESP32 (4) and AVR/Arduino (2).
How big is a typical board using the MCP6002-I/P?
The median is 102.4 × 97.6 mm, and 100% are two-layer designs.
What is the most popular open source board using the MCP6002-I/P?
By GitHub stars, FunBox by GuitarML, with 286 stars.
Can I simulate one of these boards using the MCP6002-I/P before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.