16 open source boards using the RAK3172
Real designs built with the RAK3172, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Sharpikeebo
ccadic
66 × 115.3 mm190 parts4LNo license142Feather rak3172
teapotlaboratories
51 × 23.1 mm44 parts2LMIT43Bwlr1b
teapotlaboratories
38.6 × 72.1 mm38 parts2LMIT15Bwlr1c
teapotlaboratories
38.6 × 85.3 mm35 parts2LMIT2ESP32
Mia ou
antoine-prrn
50 × 22 mm56 parts4LNo license1ESP32
Node Analog
maivananh111
83.7 × 53.7 mm130 parts2LNo license0ESP32
Plantpal
rajeev2705
38.4 × 128.5 mm110 parts4LNo license0HW-RAK3172-EaseBoard
J-Rios
50 × 60 mm46 parts2LNo license0Lorawan tenant assistant
StanZalewski
59.7 × 48.3 mm18 parts2LMIT0PrecursorLoRa
tbcolby
50 × 30 mm12 parts2LNo license0RAK3172h breadboard
ccadic
25.5 × 46.5 mm48 parts4LNo license142ESP32
Node RS485
maivananh111
83.7 × 53.7 mm116 parts2LNo license0Top
StanZalewski
100 × 66.2 mm57 parts4LNo license0ORIGINALERAK3172h breadboard
ccadic
18 × 39.5 mm38 parts2LNo license142ESP32
Node RS232
maivananh111
83.7 × 53.7 mm107 parts2LNo license0RAK3172 BREAKBOARD
galopago
29.4 × 36.8 mm4 parts2LMIT2
How designs wire the RAK3172
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the RAK3172 connects to, and the resistors, capacitors and other passives placed on it.
- The RST pin has a pull-up to 3.3V on 8 of 11 designs, most often 10 kΩ (then 1 kΩ).
- The RST pin has a capacitor to GND on 7 of 11 designs, most often 100 nF.
- The PA10/ADC4 pin is left unconnected on 8 of 11 designs (a signal on 3).
- The PB12 pin is left unconnected on 8 of 11 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PA1pin 6 | Connected to: Not connected 64% · a signal 36% | — |
| GNDpin 11, 17, 18, 23, 28 | Connected to: GND 91% | — |
| SCK/PA5pin 15 | Connected to: Not connected 64% · a signal 36% | — |
| RSTpin 22 | Connected to: A connector 45% |
|
| VCCpin 24 | Connected to: 3.3V 73% · a signal 27% |
|
| PA10/ADC4pin 25 | Connected to: Not connected 73% · a signal 27% | — |
| PB12pin 27 | Connected to: Not connected 73% · a signal 27% | — |
| PB3/ADC1pin 32 | Connected to: Not connected 64% · a signal 36% | — |
20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sharpikeebo by ccadic, Feather rak3172 by teapotlaboratories, Bwlr1b by teapotlaboratories and RAK3172 BREAKBOARD by galopago.
The RAK3172 in open source designs
The gallery holds 16 open source boards using the RAK3172 from 12 GitHub repositories; a typical one measures about 50 × 53.7 mm and carries around 47 components.
69% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is Sharpikeebo by ccadic.
Parts used alongside the RAK3172
Microcontrollers on boards using the RAK3172
What boards using the RAK3172 are built for
RAK3172: common questions
Where can I find a RAK3172 reference design?
Each of the 16 boards on this page is a real design using the RAK3172. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the RAK3172 RST pin?
The RST pin has a pull-up to 3.3V on 8 of 11 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 11 open source designs using the RAK3172.
How is the RAK3172 PA10/ADC4 pin connected?
The PA10/ADC4 pin is left unconnected on 8 of 11 designs (a signal on 3). Counted from the KiCad layouts of 11 open source designs using the RAK3172.
How is the RAK3172 PB12 pin connected?
The PB12 pin is left unconnected on 8 of 11 designs (a signal on 3). Counted from the KiCad layouts of 11 open source designs using the RAK3172.
What parts are used alongside the RAK3172?
The BME680, CH340E, MCP73831T-2ACI/OT, SP3485EN and XC6220B331MR-G appear in the most repositories here.
Which microcontrollers do boards using the RAK3172 use?
Most are built on ESP32 (5) and AVR/Arduino (1).
How big is a typical board using the RAK3172?
The median is 50 × 53.7 mm, and 69% are two-layer designs.
What is the most popular open source board using the RAK3172?
By GitHub stars, Sharpikeebo by ccadic, with 142 stars.
Can I simulate one of these boards using the RAK3172 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.