10 open source boards using the TLC555CP
Real designs built with the TLC555CP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AcCCS
IdahoLabResearch
172.1 × 143.5 mm106 parts2LMIT18AVR/Arduino
Engine monitor
alexanderenrique
50.8 × 38.1 mm60 parts2LNo license0Circuito-Disparo-Laser-CO2
FernandoVB01
100 × 70 mm45 parts2LMIT0Ir sensor strobe
bburan
37.5 × 43.5 mm27 parts2LNo license0Alternator 555 timer
alexanderenrique
38.1 × 25.4 mm18 parts2LNo license0Codex cad electronics lab
finnandreh
50 × 35 mm12 parts2LMIT0- schematic only · 11 partsESP32
Q-Flo-Prototype
adwaithas-2004
11 partsCustom license0 ESP32
Display
alexanderenrique
67.8 × 100.2 mm35 parts2LNo license0Alternator 555 timer
alexanderenrique
38.1 × 25.4 mm18 parts2LNo license0Booster-Link
GBert
50 × 50 mm28 parts2LNo license99
How designs wire the TLC555CP
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TLC555CP connects to, and the resistors, capacitors and other passives placed on it.
- The CONT_5 pin has a capacitor to GND on 7 of 7 designs, most often 100 nF (then 10 nF).
- The THRES_6 pin has a capacitor to GND on 7 of 7 designs, most often 47 µF (then 10 µF).
- The TR pin has a capacitor to GND on 6 of 7 designs, most often 100 nF (then 47 nF).
- The OUT pin has a series resistor on 6 of 7 designs, most often 1.5 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| TRpin 2 | Connected to: Signal 100% |
|
| OUTpin 3 | Connected to: A connector 43% |
|
| CONT_5pin 5 | Connected to: Signal 100% |
|
| THRES_6pin 6 | Connected to: Signal 100% |
|
| DISpin 7 | Connected to: Signal 100% |
|
| VCCpin 8 | Connected to: 5V 71% · a signal 29% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Booster-Link by GBert, AcCCS by IdahoLabResearch, Alternator 555 timer by alexanderenrique and Alternator 555 timer by alexanderenrique.
The TLC555CP in open source designs
The gallery holds 10 open source boards using the TLC555CP from 8 GitHub repositories; a typical one measures about 50 × 43.5 mm and carries around 28 components.
100% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Booster-Link by GBert.
Microcontrollers on boards using the TLC555CP
What boards using the TLC555CP are built for
TLC555CP: common questions
Where can I find a TLC555CP reference design?
Each of the 10 boards on this page is a real design using the TLC555CP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TLC555CP CONT_5 pin connected?
The CONT_5 pin has a capacitor to GND on 7 of 7 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 7 open source designs using the TLC555CP.
How is the TLC555CP THRES_6 pin connected?
The THRES_6 pin has a capacitor to GND on 7 of 7 designs, most often 47 µF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the TLC555CP.
How is the TLC555CP TR pin connected?
The TR pin has a capacitor to GND on 6 of 7 designs, most often 100 nF (then 47 nF). Counted from the KiCad layouts of 7 open source designs using the TLC555CP.
Which microcontrollers do boards using the TLC555CP use?
Most are built on ESP32 (2) and AVR/Arduino (1).
How big is a typical board using the TLC555CP?
The median is 50 × 43.5 mm, and 100% are two-layer designs.
What is the most popular open source board using the TLC555CP?
By GitHub stars, Booster-Link by GBert, with 99 stars.
Can I simulate one of these boards using the TLC555CP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.