8 open source boards using the TMP1075DSG
Real designs built with the TMP1075DSG, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
The-Surevival
Rishaan2202
51 × 23 mm72 parts2LNo license3ESP32
Lamp-2
DodoZimmermann
147 × 139.9 mm248 parts6LMIT0STM32
Aurora-Watch
CooperW824
36 × 36 mm79 parts4LMIT0ESP32
Survive
PrinceYadav78
54.7 × 23 mm72 parts4LMIT0STM32
2026 STM32
waterloo-rocketry
50 × 40 mm31 parts2LNo license0STM32
FH2 Flight Computer
EPFLRocketTeam
80 × 80 mm245 parts4LNo license0LED Module C
lenaschimmel
70 × 79.1 mm59 parts4LNo license18STM32
Flight Data Recorder
EPFLRocketTeam
50 × 40 mm89 parts4LNo license0
How designs wire the TMP1075DSG
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TMP1075DSG connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The ALERT pin has a pull-up to 3.3V on 4 of 7 designs, most often 5 kΩ (then 4.7 kΩ).
- The V+ pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SDApin 1 | Connected to: The microcontroller 57%, a connector 43% |
|
| SCLpin 2 | Connected to: The microcontroller 57%, a connector 43% |
|
| ALERTpin 3 | Connected to: The microcontroller 29% · not connected 43% |
|
| GNDpin 4 | Connected to: GND 71% · a signal 29% | — |
| V+pin 8 | Connected to: 3.3V 71% · a signal 29% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LED Module C by lenaschimmel, The-Surevival by Rishaan2202, Aurora-Watch by CooperW824 and Lamp-2 by DodoZimmermann.
The TMP1075DSG in open source designs
The gallery holds 8 open source boards using the TMP1075DSG from 7 GitHub repositories; a typical one measures about 52.9 × 40 mm and carries around 76 components.
75% use four copper layers or more, and 38% carry an open source license.
The most starred is LED Module C by lenaschimmel.
Parts used alongside the TMP1075DSG
What boards using the TMP1075DSG are built for
TMP1075DSG: common questions
Where can I find a TMP1075DSG reference design?
Each of the 8 boards on this page is a real design using the TMP1075DSG. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TMP1075DSG SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the TMP1075DSG.
What pull-up resistor is used on the TMP1075DSG SCL pin?
The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the TMP1075DSG.
What pull-up resistor is used on the TMP1075DSG ALERT pin?
The ALERT pin has a pull-up to 3.3V on 4 of 7 designs, most often 5 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the TMP1075DSG.
What parts are used alongside the TMP1075DSG?
The AO3401A, ESP32-S3FN8, HSFPAR004A, HX711 and SMD3225 appear in the most repositories here.
Which microcontrollers do boards using the TMP1075DSG use?
Most are built on STM32 (4) and ESP32 (3).
How big is a typical board using the TMP1075DSG?
The median is 52.9 × 40 mm, and 25% are two-layer designs.
What is the most popular open source board using the TMP1075DSG?
By GitHub stars, LED Module C by lenaschimmel, with 18 stars.
Can I simulate one of these boards using the TMP1075DSG before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.