6 open source boards using the TPS54202

Real designs built with the TPS54202, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the TPS54202

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS54202 connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 6 of 6 designs, most often 10 µH (then 15 µH).
  • The SW pin has a series capacitor on 6 of 6 designs, most often 100 nF.
  • The VIN pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF).
  • The FB pin has a resistor to GND on 6 of 6 designs, most often 13.7 kΩ (then 13.3 kΩ).
GNDpin 1Connected to: GND 100%
SWpin 2Connected to: Signal 100%
  • Inductor on 100% · 10 µH (2), 15 µH (2)
  • Series capacitor on 100% · 100 nF (6)
VINpin 3Connected to: A connector 50%, TMC2209-LA 33% · 12V 33%
  • Capacitor to GND on 100% · 100 nF (9), 10 µF (7), 100 µF (2)
  • Series capacitor on 33% · 100 nF (2)
  • Series resistor on 33% · 100 kΩ (1), 511 kΩ (1)
FBpin 4Connected to: Signal 100%
  • Resistor to GND on 100% · 13.7 kΩ (3), 13.3 kΩ (2), 19.2 kΩ (1)
  • Pull-up to 5V on 67% · 100 kΩ (4)
  • Series capacitor on 67% · 68 pF (2), 91 pF (1), 75 pF (1)
  • Series resistor on 33% · 100 kΩ (2)
  • Capacitor to the supply on 33% · 75 pF (1), 47 pF (1)
ENpin 5Connected to: Not connected 67% · a signal 33%
  • Series resistor on 33% · 100 kΩ (1), 511 kΩ (1), 0 Ω (1)
BOOTpin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (6)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Huvud by bondus, PiStripe uHAT by pief, Bitraf hydroponics by bitraf and AstroWeather by jakubprzybytek.

The TPS54202 in open source designs

The gallery holds 6 open source boards using the TPS54202 from 6 GitHub repositories; a typical one measures about 53.5 × 36 mm and carries around 73 components.

67% use four copper layers or more, and 33% carry an open source license.

The most starred is Huvud by bondus.

Microcontrollers on boards using the TPS54202

TPS54202: common questions

Where can I find a TPS54202 reference design?

Each of the 6 boards on this page is a real design using the TPS54202. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS54202 SW pin connected?

The SW pin has a inductor on 6 of 6 designs, most often 10 µH (then 15 µH). Counted from the KiCad layouts of 6 open source designs using the TPS54202.

How is the TPS54202 VIN pin connected?

The VIN pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the TPS54202.

What resistor goes on the TPS54202 FB pin?

The FB pin has a resistor to GND on 6 of 6 designs, most often 13.7 kΩ (then 13.3 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS54202.

What parts are used alongside the TPS54202?

The SN65HVD230, STM32F103C8T6, TMC2209-LA, TPS54331DR and XC6206PXXXMR appear in the most repositories here.

Which microcontrollers do boards using the TPS54202 use?

Most are built on STM32 (3) and ESP8266 (1).

How big is a typical board using the TPS54202?

The median is 53.5 × 36 mm, and 33% are two-layer designs.

What is the most popular open source board using the TPS54202?

By GitHub stars, Huvud by bondus, with 373 stars.

Can I simulate one of these boards using the TPS54202 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part