15 open source boards using the TPS61169DCKR

Real designs built with the TPS61169DCKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

15 boardsClear filters|Most starred

How designs wire the TPS61169DCKR

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the TPS61169DCKR connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 9 of 11 designs, most often 4.7 µH (then 10 µH).
  • The FB pin has a resistor to GND on 9 of 11 designs, most often 10 Ω (then 1.5 Ω).
  • The VIN pin has a capacitor to GND on 8 of 11 designs, most often 10 µF (then 4.7 µF).
  • The VIN pin has a inductor on 7 of 11 designs, most often 4.7 µH (then 10 µH).
SWpin 1Connected to: Signal 100%
  • Inductor on 82% · 4.7 µH (2), 10 µH (2), 6.8 µH (1)
GNDpin 2Connected to: GND 82% · a signal 18%
FBpin 3Connected to: A connector 55%
  • Resistor to GND on 82% · 10 Ω (3), 1.5 Ω (2), 2.2 Ω (1)
VINpin 5Connected to: Signal 55% · 5V 45%
  • Capacitor to GND on 73% · 10 µF (4), 4.7 µF (3), 100 nF (2)
  • Inductor on 64% · 4.7 µH (2), 10 µH (2), 1 µH (1)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EEZ BB3 CM4 R1B0 by intergalaktik, RPI CMx Carrier by lecejeff, Iris hw by bunnie and BB3plus DSI TFT display by eez-open.

The TPS61169DCKR in open source designs

The gallery holds 15 open source boards using the TPS61169DCKR from 11 GitHub repositories; a typical one measures about 136 × 84 mm and carries around 166 components.

54% use four copper layers or more, and 27% carry an open source license.

The most starred is EEZ BB3 CM4 R1B0 by intergalaktik.

Microcontrollers on boards using the TPS61169DCKR

TPS61169DCKR: common questions

Where can I find a TPS61169DCKR reference design?

Each of the 15 boards on this page is a real design using the TPS61169DCKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS61169DCKR SW pin connected?

The SW pin has a inductor on 9 of 11 designs, most often 4.7 µH (then 10 µH). Counted from the KiCad layouts of 11 open source designs using the TPS61169DCKR.

What resistor goes on the TPS61169DCKR FB pin?

The FB pin has a resistor to GND on 9 of 11 designs, most often 10 Ω (then 1.5 Ω). Counted from the KiCad layouts of 11 open source designs using the TPS61169DCKR.

How is the TPS61169DCKR VIN pin connected?

The VIN pin has a capacitor to GND on 8 of 11 designs, most often 10 µF (then 4.7 µF). Counted from the KiCad layouts of 11 open source designs using the TPS61169DCKR.

What parts are used alongside the TPS61169DCKR?

The DP83848CVV_NOPB, IS42S16400J, LD1117ADT33TR, TPD4E001DRLR and TPS2051BDBVR appear in the most repositories here.

Which microcontrollers do boards using the TPS61169DCKR use?

Most are built on STM32 (6), ESP32 (1), PIC (1) and RP2040/RP2350 (1).

How big is a typical board using the TPS61169DCKR?

The median is 136 × 84 mm, and 46% are two-layer designs.

What is the most popular open source board using the TPS61169DCKR?

By GitHub stars, EEZ BB3 CM4 R1B0 by intergalaktik, with 35 stars.

Can I simulate one of these boards using the TPS61169DCKR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part