14 open source boards using the TPS63070
Real designs built with the TPS63070, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
NIMRS-21Pin-Decoder
CDFER
30 × 23.5 mm68 parts4LNo license20Microchip SAM
Mainboard before drastic
Sierra-Lobo
90.2 × 101.1 mm353 parts6LCC-BY-SA-4.01AVR/Arduino
Payload gimbal
icl-rocketry
94 × 94 mm59 parts2LMIT1AVR/Arduino
CPRPal
Will946
78.8 × 71.9 mm41 parts2LMIT1STM32
Pcb mantis
si-nalsal
125.2 × 90 mm277 parts6LCERN-OHL-S-2.00RP2040/RP2350
Onboard Computer
onionsat-pcbs
50 × 50 mm170 parts8LNo license0ESP32
Main
jason-watkins
70 × 65 mm91 parts2LCC-BY-SA-4.00ESP32
Flex smart card
kamaljavvadi16-alt
50 × 94.5 mm62 parts4LNo license0Umich balloons power
EricAndrechek
66 × 53.3 mm17 parts2LNo license0Tps63070-3v3-dev board
eshelton328
24.7 × 22.9 mm15 parts2LNo license0Microchip SAM
Mainboard
Sierra-Lobo
90.2 × 101.1 mm312 parts6LCC-BY-SA-4.01Tc2-plugs buck boost
TheCacophonyProject
65 × 19.5 mm65 parts6LCERN-OHL-W-2.00ESP32
Umich balloons processor
EricAndrechek
66 × 53.3 mm4 parts2LNo license0Umich balloons gps
EricAndrechek
66 × 53.3 mm3 parts2LNo license0
How designs wire the TPS63070
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the TPS63070 connects to, and the resistors, capacitors and other passives placed on it.
- The VAUX pin has a capacitor to GND on 9 of 10 designs, most often 100 nF.
- The FB pin has a resistor to GND on 9 of 10 designs, most often 150 kΩ (then 68.1 kΩ).
- The L2 pin has a inductor on 9 of 10 designs, most often 1.5 µH (then 1 µH).
- The L1 pin has a inductor on 9 of 10 designs, most often 1.5 µH (then 1 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PS/SYNCpin 1 | Connected to: A connector 30% |
|
| PGpin 2 | Connected to: The microcontroller 20%, a connector 20% · not connected 20% |
|
| VAUXpin 3 | Connected to: Signal 90% |
|
| GNDpin 4 | Connected to: GND 90% | — |
| FBpin 5 | Connected to: Signal 90% |
|
| FB2pin 6 | Connected to: GND 70% | — |
| VOUTpin 7, 8 | Connected to: A connector 46% · 3.3V 46% |
|
| L2pin 9 | Connected to: Signal 80% |
|
| PGNDpin 10 | Connected to: GND 90% | — |
| L1pin 11 | Connected to: Signal 80% · 3V 20% |
|
| VINpin 12, 13 | Connected to: A connector 31% · not connected 15% · VIN 38% |
|
| ENpin 14 | Connected to: A connector 20% |
|
| VSELpin 15 | Connected to: GND 80% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include NIMRS-21Pin-Decoder by CDFER, Payload gimbal by icl-rocketry, CPRPal by Will946 and Umich balloons gps by EricAndrechek.
The TPS63070 in open source designs
The gallery holds 14 open source boards using the TPS63070 from 11 GitHub repositories; a typical one measures about 66 × 59.2 mm and carries around 64 components.
50% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is NIMRS-21Pin-Decoder by CDFER.
Parts used alongside the TPS63070
Microcontrollers on boards using the TPS63070
What boards using the TPS63070 are built for
TPS63070: common questions
Where can I find a TPS63070 reference design?
Each of the 14 boards on this page is a real design using the TPS63070. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS63070 VAUX pin connected?
The VAUX pin has a capacitor to GND on 9 of 10 designs, most often 100 nF. Counted from the KiCad layouts of 10 open source designs using the TPS63070.
What resistor goes on the TPS63070 FB pin?
The FB pin has a resistor to GND on 9 of 10 designs, most often 150 kΩ (then 68.1 kΩ). Counted from the KiCad layouts of 10 open source designs using the TPS63070.
How is the TPS63070 L2 pin connected?
The L2 pin has a inductor on 9 of 10 designs, most often 1.5 µH (then 1 µH). Counted from the KiCad layouts of 10 open source designs using the TPS63070.
Which microcontrollers do boards using the TPS63070 use?
Most are built on ESP32 (4), AVR/Arduino (2), Microchip SAM (2) and RP2040/RP2350 (1).
How big is a typical board using the TPS63070?
The median is 66 × 59.2 mm, and 50% are two-layer designs.
What is the most popular open source board using the TPS63070?
By GitHub stars, NIMRS-21Pin-Decoder by CDFER, with 20 stars.
Can I simulate one of these boards using the TPS63070 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.