17 open source boards using the 24LC32
Real designs built with the 24LC32, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Ir clone
dilshan
32.1 × 41.2 mm35 parts2LMIT58Raspberry Pi
OpenPLC
radioelf
129.5 × 72.6 mm163 parts2LNo license7STM32
Quad adsr
JordanAceto
71.1 × 99.1 mm197 parts2LNo license5Kicad 7 cli doc gen
JordanAceto
33 × 50.8 mm50 parts4LMIT5- schematic only · 8 parts
Neuroboard
Be-bibek
8 partsMIT3 STM32
Elec Poulpe 3d
pollen-robotics
45 × 86.6 mm211 parts4LApache-2.02STM32
Elec Poulpe 2d
pollen-robotics
59 × 73 mm194 parts4LApache-2.01RP2040/RP2350
Gaugeflow
cclienti
72 × 61 mm22 parts2LGPL-3.01STM32
PCB ApiaryWaterDispensingSystem
Mateuszworo97
217.3 × 127.3 mm182 parts2LNo license0Raspberry Pi
Vinyl adc rev d
MadsRudolph
140 × 136 mm177 parts4LNo license0AA PwrSens Dist
AESilky
147.3 × 154.4 mm135 parts2LNo license0RP2040/RP2350
Berryboard
curtisgalloway
56 × 65 mm58 parts2LNo license0STM32
Sensor node
henriheimann
57 × 57 mm49 partsNo license0ESP32
Sump pump monitor
patrick-th
68 × 114.5 mm40 parts2LNo license0Raspberry Pi
Vinyl adc rev e
MadsRudolph
118 × 88 mm177 parts4LNo license0STM32
Irrgiation sensor rev4-3
henriheimann
180 × 38 mm35 parts2LNo license0Band Switch board 2026 small
satspares
90 × 45 mm31 parts2LMIT0
How designs wire the 24LC32
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the 24LC32 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 11 of 14 designs, most often 100 nF (then 10 µF).
- The A1 pin is tied to GND on 13 of 14 designs.
- The A2 pin is tied to GND on 13 of 14 designs.
- The WP pin is tied to GND on 13 of 14 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 79% · a signal 21% | — |
| A1pin 2 | Connected to: GND 93% | — |
| A2pin 3 | Connected to: GND 93% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: A connector 50%, the microcontroller 36% |
|
| SCLpin 6 | Connected to: A connector 50%, the microcontroller 36% |
|
| WPpin 7 | Connected to: GND 93% | — |
| VCCpin 8 | Connected to: 3.3V 93% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ir clone by dilshan, OpenPLC by radioelf, Kicad 7 cli doc gen by JordanAceto and Quad adsr by JordanAceto.
The 24LC32 in open source designs
The gallery holds 17 open source boards using the 24LC32 from 15 GitHub repositories; a typical one measures about 71.6 × 72.8 mm and carries around 58 components.
67% are two-layer designs, the rest use four layers or more, and 41% carry an open source license.
The most starred is Ir clone by dilshan.
Parts used alongside the 24LC32
Microcontrollers on boards using the 24LC32
What boards using the 24LC32 are built for
24LC32: common questions
Where can I find a 24LC32 reference design?
Each of the 17 boards on this page is a real design using the 24LC32. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 24LC32 VCC pin?
The VCC pin has a decoupling capacitor on 11 of 14 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 14 open source designs using the 24LC32.
How is the 24LC32 A1 pin connected?
The A1 pin is tied to GND on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the 24LC32.
How is the 24LC32 A2 pin connected?
The A2 pin is tied to GND on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the 24LC32.
What parts are used alongside the 24LC32?
The AMS1117-3.3, ADS1015IDGS, BMI088, LAN9252 and STM32H742/3VxTx appear in the most repositories here.
Which microcontrollers do boards using the 24LC32 use?
Most are built on STM32 (7), Raspberry Pi (3), RP2040/RP2350 (2) and ESP32 (1).
How big is a typical board using the 24LC32?
The median is 71.6 × 72.8 mm, and 67% are two-layer designs.
What is the most popular open source board using the 24LC32?
By GitHub stars, Ir clone by dilshan, with 58 stars.
Can I simulate one of these boards using the 24LC32 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.