6 open source boards using the AP2553W6-7
Real designs built with the AP2553W6-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
HALPI2-hardware
hatlabs
187 × 109 mm541 parts6LCustom license9Tablet-Project
ShresthRao
40.3 × 155 mm115 parts4LNo license0Neapolitan
Josephrp
120 × 75 mm290 partsCustom license12Neapolitan
greearb
120 × 75 mm290 partsGPL-2.01Neapolitan
JensLiu
120 × 75 mm290 partsGPL-2.01Neapolitan
deepin-community
120 × 75 mm290 partsGPL-2.00
How designs wire the AP2553W6-7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AP2553W6-7 connects to, and the resistors, capacitors and other passives placed on it.
- The IN_1 pin has a capacitor to GND on 5 of 6 designs, most often 1 µF (then 10 µF).
- The IN_1 pin has a series resistor on 4 of 6 designs, most often 10 kΩ.
- The EN_3 pin has a resistor to GND on 4 of 6 designs, most often 10 kΩ.
- The FAULT_4 pin has a series resistor on 4 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN_1pin 1 | Connected to: MAX2837 67%, RFFC5072 67%, a connector 67% · 5V 33% |
|
| GND_2pin 2 | Connected to: GND 100% | — |
| EN_3pin 3 | Connected to: RFFC5072 67%, a connector 67% · 5V 33% |
|
| FAULT_4pin 4 | Connected to: A connector 67% · not connected 33% |
|
| ILIM_5pin 5 | Connected to: GND 67% · a signal 33% |
|
| OUT_6pin 6 | Connected to: Signal 83% · 5V 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Neapolitan by Josephrp, HALPI2-hardware by hatlabs, Neapolitan by greearb and Neapolitan by JensLiu.
The AP2553W6-7 in open source designs
The gallery holds 6 open source boards using the AP2553W6-7 from 6 GitHub repositories; a typical one measures about 120 × 75 mm and carries around 290 components.
100% use four copper layers or more, and 50% carry an open source license.
The most starred is Neapolitan by Josephrp.
Parts used alongside the AP2553W6-7
Microcontrollers on boards using the AP2553W6-7
What boards using the AP2553W6-7 are built for
AP2553W6-7: common questions
Where can I find a AP2553W6-7 reference design?
Each of the 6 boards on this page is a real design using the AP2553W6-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP2553W6-7 IN_1 pin connected?
The IN_1 pin has a capacitor to GND on 5 of 6 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the AP2553W6-7.
What resistor goes on the AP2553W6-7 EN_3 pin?
The EN_3 pin has a resistor to GND on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the AP2553W6-7.
What resistor goes on the AP2553W6-7 FAULT_4 pin?
The FAULT_4 pin has a series resistor on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the AP2553W6-7.
What parts are used alongside the AP2553W6-7?
The 74LVC1G14, MAX2837, MGA-81563, RFFC5072 and RX_HIGHPASS_FILTER appear in the most repositories here.
Which microcontrollers do boards using the AP2553W6-7 use?
Most are built on RP2040/RP2350 (1).
How big is a typical board using the AP2553W6-7?
The median is 120 × 75 mm, and 0% are two-layer designs.
What is the most popular open source board using the AP2553W6-7?
By GitHub stars, Neapolitan by Josephrp, with 12 stars.
Can I simulate one of these boards using the AP2553W6-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.