17 open source boards using the Arduino Nano v3

Real designs built with the Arduino Nano v3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the Arduino Nano v3

Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the Arduino Nano v3 connects to, and the resistors, capacitors and other passives placed on it.

  • The D0/RX pin is left unconnected on 10 of 10 designs.
  • The AREF pin is left unconnected on 10 of 10 designs.
  • The D1/TX pin is left unconnected on 9 of 10 designs.
  • The A6 pin is left unconnected on 9 of 10 designs.
D1/TXpin 1Connected to: Not connected 90%
D0/RXpin 2Connected to: Not connected 100%
RESETpin 3, 28Connected to: Not connected 75% · a signal 25%
  • Pull-up to 5V on 30% · 100 kΩ (3)
GNDpin 4, 29Connected to: GND 70% · a signal 20%
D2pin 5Connected to: Not connected 50% · a signal 50%
  • Series resistor on 30% · 100 Ω (3)
D3pin 6Connected to: Not connected 70% · a signal 30%
D6pin 9Connected to: ADG1611 30%, a connector 20% · not connected 30%
  • Pull-up to VDD on 30% · 10 kΩ (3)
D7pin 10Connected to: ADG1611 30%, a connector 20% · not connected 30%
  • Pull-up to VDD on 30% · 10 kΩ (3)
D8pin 11Connected to: Not connected 70% · a signal 30%
D9pin 12Connected to: Not connected 80% · a signal 20%
D12pin 15Connected to: Not connected 50% · a signal 50%
  • Pull-up to 5V on 30% · 4.7 kΩ (3)
D13pin 16Connected to: 74LVC125 20% · not connected 30%
  • Pull-up to 5V on 30% · 4.7 kΩ (3)
3V3pin 17Connected to: Not connected 80% · 3.3V 20%
AREFpin 18Connected to: Not connected 100%
A0pin 19Connected to: Not connected 80% · a signal 20%
A1pin 20Connected to: Not connected 80% · a signal 20%
A2pin 21Connected to: Not connected 80% · a signal 20%
A3pin 22Connected to: Not connected 80% · a signal 20%
A6pin 25Connected to: Not connected 90%
A7pin 26Connected to: Not connected 90%
+5Vpin 27Connected to: 5V 90%
VINpin 30Connected to: Not connected 80%

6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Drift by QuinnFreedman, Sdbox by jbilander, SDBox v2 by jbilander and Wii-BVM-Card by Shank-Mods.

The Arduino Nano v3 in open source designs

The gallery holds 17 open source boards using the Arduino Nano v3 from 14 GitHub repositories; a typical one measures about 90 × 87.8 mm and carries around 23 components.

100% are two-layer designs, the rest use four layers or more, and 53% carry an open source license.

The most starred is RNG Back by QuinnFreedman.

Parts used alongside the Arduino Nano v3

Microcontrollers on boards using the Arduino Nano v3

Arduino Nano v3: common questions

Where can I find a Arduino Nano v3 reference design?

Each of the 17 boards on this page is a real design using the Arduino Nano v3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the Arduino Nano v3 D0/RX pin connected?

The D0/RX pin is left unconnected on 10 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the Arduino Nano v3.

How is the Arduino Nano v3 AREF pin connected?

The AREF pin is left unconnected on 10 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the Arduino Nano v3.

How is the Arduino Nano v3 D1/TX pin connected?

The D1/TX pin is left unconnected on 9 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the Arduino Nano v3.

What parts are used alongside the Arduino Nano v3?

The ADG1611, THS7374, 74LVC125 and MIC3490-3.3 appear in the most repositories here.

Which microcontrollers do boards using the Arduino Nano v3 use?

Most are built on AVR/Arduino (17).

How big is a typical board using the Arduino Nano v3?

The median is 90 × 87.8 mm, and 100% are two-layer designs.

What is the most popular open source board using the Arduino Nano v3?

By GitHub stars, RNG Back by QuinnFreedman, with 114 stars.

Can I simulate one of these boards using the Arduino Nano v3 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part