12 open source boards using the BQ25186DLHR
Real designs built with the BQ25186DLHR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Storm tracker hardware
solderable
36.5 × 69 mm79 parts4LNo license56Chloroplast
badjeff
18 × 33 mm27 parts2LNo license5ESP32
Candidate
earlynerd
21 × 55.9 mm261 parts4LNo license0ESP32
Handset
JeremyLakeyJr
66 × 142 mm217 parts4LNo license0Nordic nRF
Aura a04
Avinash1286
35.2 × 35.2 mm72 parts4LMIT0AVR/Arduino
BinaryClock
kwame-y
60 × 30 mm52 parts4LNo license0ESP32
Merged
earlynerd
21 × 55.9 mm261 parts4LNo license0ESP32
Input
earlynerd
21 × 55.9 mm69 parts4LNo license0Nordic nRF
Knuckles integrated right
fcoury
137.3 × 113.5 mm100 parts4LMIT6ESP32
Main
earlynerd
20 × 46 mm47 parts4LNo license0Nordic nRF
Knuckles integrated left
fcoury
130.3 × 107.9 mm99 parts4LMIT6Nordic nRF
Knuckles controller
fcoury
45 × 55 mm41 parts2LMIT6
How designs wire the BQ25186DLHR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the BQ25186DLHR connects to, and the resistors, capacitors and other passives placed on it.
- The BAT_2 pin is tied to VBAT on 6 of 6 designs.
- The BAT_2 pin has a decoupling capacitor on 5 of 6 designs, most often 10 µF (then 2.2 µF).
- The SDA_7 pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL_8 pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BAT_2pin 2 | Connected to: VBAT 100% |
|
| CE_4pin 4 | Connected to: Signal 83% · not connected 17% |
|
| GND_5pin 5 | Connected to: GND 100% | — |
| TS/MR_6pin 6 | Connected to: A connector 67% |
|
| SDA_7pin 7 | Connected to: The microcontroller 83% |
|
| SCL_8pin 8 | Connected to: The microcontroller 83% |
|
| INT_9pin 9 | Connected to: The microcontroller 67% · not connected 17% |
|
| IN_10pin 10 | Connected to: Signal 67% · 5V 33% |
|
| GND_11pin 11 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Storm tracker hardware by solderable, Knuckles controller by fcoury, Chloroplast pcb by badjeff and Candidate by earlynerd.
The BQ25186DLHR in open source designs
The gallery holds 12 open source boards using the BQ25186DLHR from 7 GitHub repositories; a typical one measures about 35.9 × 55.9 mm and carries around 76 components.
83% use four copper layers or more, and 33% carry an open source license.
The most starred is Storm tracker hardware by solderable.
Parts used alongside the BQ25186DLHR
Microcontrollers on boards using the BQ25186DLHR
What boards using the BQ25186DLHR are built for
BQ25186DLHR: common questions
Where can I find a BQ25186DLHR reference design?
Each of the 12 boards on this page is a real design using the BQ25186DLHR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the BQ25186DLHR BAT_2 pin connected?
The BAT_2 pin is tied to VBAT on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the BQ25186DLHR.
What pull-up resistor is used on the BQ25186DLHR SDA_7 pin?
The SDA_7 pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the BQ25186DLHR.
What pull-up resistor is used on the BQ25186DLHR SCL_8 pin?
The SCL_8 pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the BQ25186DLHR.
What parts are used alongside the BQ25186DLHR?
The MDBT50Q-1MV2, TPS2553DBVR, TPS63802DLAR and TUSB320LAIRWBR appear in the most repositories here.
Which microcontrollers do boards using the BQ25186DLHR use?
Most are built on ESP32 (6), Nordic nRF (4) and AVR/Arduino (1).
How big is a typical board using the BQ25186DLHR?
The median is 35.9 × 55.9 mm, and 17% are two-layer designs.
What is the most popular open source board using the BQ25186DLHR?
By GitHub stars, Storm tracker hardware by solderable, with 56 stars.
Can I simulate one of these boards using the BQ25186DLHR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.