28 open source boards using the TUSB320LAIRWBR

Real designs built with the TUSB320LAIRWBR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

28 boardsClear filters|Most starred

How designs wire the TUSB320LAIRWBR

Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the TUSB320LAIRWBR connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin is tied to GND on 13 of 14 designs.
  • The SDA/OUT1 pin has a pull-up to 3.3V on 10 of 14 designs, most often 4.7 kΩ (then 100 kΩ).
  • The SCL/OUT2 pin has a pull-up to 3.3V on 10 of 14 designs, most often 4.7 kΩ (then 100 kΩ).
  • The ID pin is left unconnected on 12 of 14 designs (a signal on 2).
PORTpin 3Connected to: GND 79%
VBUS_DETpin 4Connected to: Signal 79% · VBUS_DET 21%
  • Pull-up to VBUS on 50% · 900 kΩ (3), 887 kΩ (3), 1 MΩ (1)
INT/OUT3pin 6Connected to: Not connected 50% · a signal 50%
  • Pull-up to 3.3V on 43% · 10 kΩ (4), 200 kΩ (1), 100 kΩ (1)
SDA/OUT1pin 7Connected to: The microcontroller 50%
  • Pull-up to 3.3V on 71% · 4.7 kΩ (5), 100 kΩ (2), 10 kΩ (2)
SCL/OUT2pin 8Connected to: The microcontroller 50%
  • Pull-up to 3.3V on 71% · 4.7 kΩ (5), 100 kΩ (2), 10 kΩ (2)
IDpin 9Connected to: Not connected 86%
GNDpin 10Connected to: GND 93%
ENpin 11Connected to: GND 93%
VDDpin 12Connected to: 3.3V 71% · a signal 29%
  • Decoupling capacitor on 64% · 100 nF (13), 1 µF (2), 220 nF (1)

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Moto gps rev a1 by mx3353672833-debug, EUB-04 Emiuet by emnyeca, MagMouse by sbarisic and EEG-PCB by MariusFauteux.

The TUSB320LAIRWBR in open source designs

The gallery holds 28 open source boards using the TUSB320LAIRWBR from 14 GitHub repositories; a typical one measures about 70 × 55.9 mm and carries around 95 components.

54% use four copper layers or more, and 50% carry an open source license.

The most starred is Moto gps rev a1 by mx3353672833-debug.

Microcontrollers on boards using the TUSB320LAIRWBR

TUSB320LAIRWBR: common questions

Where can I find a TUSB320LAIRWBR reference design?

Each of the 28 boards on this page is a real design using the TUSB320LAIRWBR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TUSB320LAIRWBR EN pin connected?

The EN pin is tied to GND on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the TUSB320LAIRWBR.

What pull-up resistor is used on the TUSB320LAIRWBR SDA/OUT1 pin?

The SDA/OUT1 pin has a pull-up to 3.3V on 10 of 14 designs, most often 4.7 kΩ (then 100 kΩ). Counted from the KiCad layouts of 14 open source designs using the TUSB320LAIRWBR.

What pull-up resistor is used on the TUSB320LAIRWBR SCL/OUT2 pin?

The SCL/OUT2 pin has a pull-up to 3.3V on 10 of 14 designs, most often 4.7 kΩ (then 100 kΩ). Counted from the KiCad layouts of 14 open source designs using the TUSB320LAIRWBR.

What parts are used alongside the TUSB320LAIRWBR?

The TPD2EUSB30DRTR, TPS63070RNMR, SN74LVC1G17DBVR, TPS2553DBVR and ESP32-S3-WROOM-1U-N16R8 appear in the most repositories here.

Which microcontrollers do boards using the TUSB320LAIRWBR use?

Most are built on ESP32 (14) and RP2040/RP2350 (12).

How big is a typical board using the TUSB320LAIRWBR?

The median is 70 × 55.9 mm, and 46% are two-layer designs.

What is the most popular open source board using the TUSB320LAIRWBR?

By GitHub stars, Moto gps rev a1 by mx3353672833-debug, with 320 stars.

Can I simulate one of these boards using the TUSB320LAIRWBR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part