12 open source boards using the ECS-1612MV-250-CN
Real designs built with the ECS-1612MV-250-CN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Reworkctf
azonenberg
54 × 50 mm125 parts4LBSD-3-Clause33STM32
Main
azonenberg
130 × 90 mm435 parts10LBSD-3-Clause17STM32
Kup lulz
azonenberg
154.5 × 137 mm376 parts4LBSD-3-Clause17STM32
Mainboard
azonenberg
165 × 121 mm617 parts10LBSD-3-Clause7- schematic only · 191 partsSTM32
Ayrton
azonenberg
191 partsBSD-3-Clause4 - schematic only · 80 partsSTM32
Grover
azonenberg
80 partsBSD-3-Clause2 STM32
Switch engine
azonenberg
151 × 111 mm362 parts10LBSD-3-Clause35STM32
Fpga stm32-ifaces
azonenberg
90 × 94.5 mm267 parts6LBSD-3-Clause17STM32
Lcbringup
azonenberg
93 × 69 mm198 parts4LBSD-3-Clause35STM32
Baset1-media converter
azonenberg
100.5 × 62.5 mm173 parts4LBSD-3-Clause17FPGA
Fpga test kintex676-artix484
azonenberg
73 × 88 mm152 parts4LBSD-3-Clause17Lpr rgmii phy
azonenberg
35 × 73.5 mm82 parts4LBSD-3-Clause17
How designs wire the ECS-1612MV-250-CN
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ECS-1612MV-250-CN connects to, and the resistors, capacitors and other passives placed on it.
- The CLK pin has a series resistor on 5 of 5 designs, most often 33 Ω.
- The VDD pin has a decoupling capacitor on 5 of 5 designs, most often 470 nF (then 10 µF).
- The E/D# pin is tied to 3.3V on 5 of 5 designs.
- The E/D# pin has a ferrite bead on 3 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| E/D#pin 1 | Connected to: 3.3V 100% |
|
| VSSpin 2 | Connected to: GND 100% | — |
| CLKpin 3 | Connected to: Signal 100% |
|
| VDDpin 4 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lcbringup by azonenberg, Reworkctf by azonenberg, Main pcb by azonenberg and Baset1-media converter by azonenberg.
The ECS-1612MV-250-CN in open source designs
The gallery holds 12 open source boards using the ECS-1612MV-250-CN from 7 GitHub repositories; a typical one measures about 96.8 × 89 mm and carries around 195 components.
100% use four copper layers or more, and 100% carry an open source license.
The most starred is Switch engine by azonenberg.
Parts used alongside the ECS-1612MV-250-CN
What boards using the ECS-1612MV-250-CN are built for
ECS-1612MV-250-CN: common questions
Where can I find a ECS-1612MV-250-CN reference design?
Each of the 12 boards on this page is a real design using the ECS-1612MV-250-CN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the ECS-1612MV-250-CN CLK pin?
The CLK pin has a series resistor on 5 of 5 designs, most often 33 Ω. Counted from the KiCad layouts of 5 open source designs using the ECS-1612MV-250-CN.
What decoupling capacitors do designs use on the ECS-1612MV-250-CN VDD pin?
The VDD pin has a decoupling capacitor on 5 of 5 designs, most often 470 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the ECS-1612MV-250-CN.
How is the ECS-1612MV-250-CN E/D# pin connected?
The E/D# pin is tied to 3.3V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ECS-1612MV-250-CN.
What parts are used alongside the ECS-1612MV-250-CN?
The AT24MAC402, KSZ9031RN, STM32H735-UFBGA176-25, 74LVC1T45 and RCLAMP0514M appear in the most repositories here.
Which microcontrollers do boards using the ECS-1612MV-250-CN use?
Most are built on STM32 (10) and FPGA (1).
How big is a typical board using the ECS-1612MV-250-CN?
The median is 96.8 × 89 mm, and 0% are two-layer designs.
What is the most popular open source board using the ECS-1612MV-250-CN?
By GitHub stars, Switch engine by azonenberg, with 35 stars.
Can I simulate one of these boards using the ECS-1612MV-250-CN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.