19 open source boards using the LM4562
Real designs built with the LM4562, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Easysdr
michalin
67.3 × 74.9 mm32 parts2LGPL-3.0114AVR/Arduino
Software-Defined-Radio
Dizzerin
81.3 × 33.7 mm62 parts2LNo license24RP2040/RP2350
QO100 RX
barisdinc
97 × 97 mm162 parts2LGPL-3.020STM32
Dac
sambazley
100 × 64.9 mm86 parts2LNo license3AVR/Arduino
Corrected ENGR357 Project v1.1
pricna
100 × 100 mm80 parts2LMPL-2.03Mixer-W-Output-HP
twam
50 × 50 mm79 parts4LNo license2FPGA
AsD Preamp Digital Preamplifier
djupdal
130 × 140 mm271 parts4LNo license1Bottom board
mod-audio
172 × 140.5 mm252 parts2LNo license1RP2040/RP2350
Rf switchboard
Erhannis
100 × 174.6 mm463 parts4LNo license0Aurora icepower booster
jpsamuelson
145.6 × 200 mm265 parts2LNo license0Maria phono preamp
sibiryakov
150 × 100 mm115 parts2LMIT0NXP
Mcguitarpedal
frsaba
123 × 113.5 mm113 parts2LNo license0Digital tone
barrybridges68
80 × 80 mm96 parts2LGPL-3.00Quadrature TX/RX Board
brucemack
70 × 100 mm92 parts4LGPL-3.00AVR/Arduino
SDR SSB
kholia
85.1 × 71.7 mm70 parts2LNo license15AVR/Arduino
ENGR357 Project v1.1
pricna
74 × 72.1 mm66 parts2LMPL-2.03Tx-1
brucemack
68 × 41 mm51 parts2LGPL-3.00Kc1fsz rx6
brucemack
60.3 × 46.5 mm48 parts2LGPL-3.00AVR/Arduino
DDS Modul 2
apxco
100 × 84 mm68 parts2LNo license0
How designs wire the LM4562
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the LM4562 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 14 of 16 designs, most often 100 nF (then 10 µF).
- Pin 1 has a series capacitor on 13 of 16 designs, most often 1 nF (then 10 µF).
- The - pins have a series capacitor on 13 of 16 designs, most often 1 nF (then 4.7 nF).
- The - pins have a series resistor on 13 of 16 designs, most often 10 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 94% |
|
| -pin 2, 6 | Connected to: Signal 91% |
|
| +pin 3, 5 | Connected to: Signal 88% |
|
| V-pin 4 | Connected to: GND 69% · a signal 19% |
|
| Pin 7 | Connected to: Signal 88% |
|
| V+pin 8 | Connected to: 5V 94% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Easysdr by michalin, Software-Defined-Radio by Dizzerin, QO100 RX by barisdinc and SDR SSB by kholia.
The LM4562 in open source designs
The gallery holds 19 open source boards using the LM4562 from 16 GitHub repositories; a typical one measures about 97 × 84 mm and carries around 86 components.
79% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.
The most starred is Easysdr by michalin.
Parts used alongside the LM4562
Microcontrollers on boards using the LM4562
What boards using the LM4562 are built for
LM4562: common questions
Where can I find a LM4562 reference design?
Each of the 19 boards on this page is a real design using the LM4562. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LM4562 V+ pin?
The V+ pin has a decoupling capacitor on 14 of 16 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 16 open source designs using the LM4562.
How is the LM4562 pin 1 connected?
Pin 1 has a series capacitor on 13 of 16 designs, most often 1 nF (then 10 µF). Counted from the KiCad layouts of 16 open source designs using the LM4562.
How is the LM4562 - pin connected?
The - pins have a series capacitor on 13 of 16 designs, most often 1 nF (then 4.7 nF). Counted from the KiCad layouts of 16 open source designs using the LM4562.
What parts are used alongside the LM4562?
The Si5351A-B-GT, SN74CBT3253, Arduino_Nano_v3.x, DIR9001 and LM1117-5.0 appear in the most repositories here.
Which microcontrollers do boards using the LM4562 use?
Most are built on AVR/Arduino (5), RP2040/RP2350 (2), ESP32 (1) and FPGA (1).
How big is a typical board using the LM4562?
The median is 97 × 84 mm, and 79% are two-layer designs.
What is the most popular open source board using the LM4562?
By GitHub stars, Easysdr by michalin, with 114 stars.
Can I simulate one of these boards using the LM4562 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.