11 open source boards using the MCP47A1
Real designs built with the MCP47A1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Soldered Inkplate 4 TEMPERA with glass panel
SolderedElectronics
72 × 78 mm246 parts4LTAPR-OHL-1.05ESP32
Soldered Inkplate 6 FLICK
SolderedElectronics
150.4 × 107.8 mm329 parts2LTAPR-OHL-1.02ESP32
Soldered Inkplate 6PLUS
SolderedElectronics
144.4 × 107.8 mm242 parts2LTAPR-OHL-1.02ESP32
Soldered Inkplate 6PLUS
SolderedElectronics
144.4 × 107.8 mm242 parts2LTAPR-OHL-1.01DAC-6-bit-1-channel-MCP47A1-breakout hardware design
SolderedElectronics
22 × 38 mm15 parts2LTAPR-OHL-1.00Soldered-DAC-6-bit-1-channel-MCP47A1-breakout hardware design
test-gh-syncer2
22 × 38 mm15 parts2LTAPR-OHL-1.00ESP32
Soldered Inkplate 4 TEMPERA with glass panel panel
SolderedElectronics
1.9 × 12 mm246 parts4LTAPR-OHL-1.05ESP32
Soldered Inkplate 6 FLICK panel
SolderedElectronics
33.7 × 6.2 mm329 parts2LTAPR-OHL-1.02ESP32
Inkplate 6PLUS panel
SolderedElectronics
294.8 × 119.8 mm241 parts2LTAPR-OHL-1.02ESP32
Inkplate 6PLUS panel
SolderedElectronics
294.8 × 119.8 mm241 parts2LTAPR-OHL-1.01ESP32
Soldered Inkplate 6FLICK Gen2
SolderedElectronics
144.4 × 107.8 mm247 parts2LTAPR-OHL-1.02
How designs wire the MCP47A1
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP47A1 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a capacitor to GND on 4 of 6 designs, most often 100 nF (then 1 µF).
- The SCL pin has a series resistor on 4 of 6 designs, most often 10 kΩ.
- The VOUT pin has a series resistor on 4 of 6 designs, most often 47 kΩ.
- The VREF pin has a capacitor to GND on 4 of 6 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: Signal 67% · VCC 33% |
|
| VSSpin 2 | Connected to: GND 67% · a signal 33% |
|
| SCLpin 3 | Connected to: PCF85063A 50%, the microcontroller 33%, TPS65186RGZ 33% |
|
| SDApin 4 | Connected to: PCF85063A 50%, the microcontroller 33%, TPS65186RGZ 33% |
|
| VOUTpin 5 | Connected to: Signal 100% |
|
| VREFpin 6 | Connected to: Signal 67% · VCC 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Soldered Inkplate 4 TEMPERA with glass panel by SolderedElectronics, Soldered Inkplate 6 FLICK by SolderedElectronics, Inkplate 6PLUS panel by SolderedElectronics and Inkplate 6PLUS panel by SolderedElectronics.
The MCP47A1 in open source designs
The gallery holds 11 open source boards using the MCP47A1 from 6 GitHub repositories; a typical one measures about 144.4 × 107.8 mm and carries around 242 components.
82% are two-layer designs, the rest use four layers or more, and 100% carry an open source license.
The most starred is Soldered Inkplate 4 TEMPERA with glass panel by SolderedElectronics.
Parts used alongside the MCP47A1
Microcontrollers on boards using the MCP47A1
What boards using the MCP47A1 are built for
MCP47A1: common questions
Where can I find a MCP47A1 reference design?
Each of the 11 boards on this page is a real design using the MCP47A1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP47A1 VDD pin connected?
The VDD pin has a capacitor to GND on 4 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the MCP47A1.
What resistor goes on the MCP47A1 SCL pin?
The SCL pin has a series resistor on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the MCP47A1.
What resistor goes on the MCP47A1 VOUT pin?
The VOUT pin has a series resistor on 4 of 6 designs, most often 47 kΩ. Counted from the KiCad layouts of 6 open source designs using the MCP47A1.
What parts are used alongside the MCP47A1?
The AP5726WG-7, CH340C, ESP32-WROVER, MC14093BDTR2G and MCP73831T appear in the most repositories here.
Which microcontrollers do boards using the MCP47A1 use?
Most are built on ESP32 (9).
How big is a typical board using the MCP47A1?
The median is 144.4 × 107.8 mm, and 82% are two-layer designs.
What is the most popular open source board using the MCP47A1?
By GitHub stars, Soldered Inkplate 4 TEMPERA with glass panel by SolderedElectronics, with 5 stars.
Can I simulate one of these boards using the MCP47A1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.