44 open source boards using the MQ-X

Real designs built with the MQ-X, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

44 boardsClear filters|Most starred

How designs wire the MQ-X

Read from the KiCad layouts of 44 open source designs, one per repository: what each pin of the MQ-X connects to, and the resistors, capacitors and other passives placed on it.

  • The B pins have a resistor to GND on 43 of 44 designs, most often 10 kΩ.
  • The A pins is tied to 5V on 98% of them (a signal on 2).
  • The B pins have a capacitor to GND on 18 of 44 designs, most often 100 nF.
Apin 1, 3Connected to: 5V 98%
Bpin 4, 6Connected to: The microcontroller 57%, LM393 41%
  • Resistor to GND on 98% · 10 kΩ (86)
  • Capacitor to GND on 41% · 100 nF (36)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Air quality sensor-MQ135-breakout hardware design by SolderedElectronics, CO-sensor-MQ7-breakout hardware design by SolderedElectronics, Ozone sensor-MQ131-breakout hardware design by SolderedElectronics and Ammonia sensor-MQ137-breakout hardware design by SolderedElectronics.

The MQ-X in open source designs

The gallery holds 44 open source boards using the MQ-X from 44 GitHub repositories; a typical one measures about 22 × 54 mm and carries around 26 components.

100% are two-layer designs, the rest use four layers or more, and 100% carry an open source license.

The most starred is Air quality sensor-MQ135-breakout hardware design by SolderedElectronics.

Microcontrollers on boards using the MQ-X

What boards using the MQ-X are built for

MQ-X: common questions

Where can I find a MQ-X reference design?

Each of the 44 boards on this page is a real design using the MQ-X. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the MQ-X B pin?

The B pins have a resistor to GND on 43 of 44 designs, most often 10 kΩ. Counted from the KiCad layouts of 44 open source designs using the MQ-X.

How is the MQ-X A pin connected?

The A pins is tied to 5V on 98% of them (a signal on 2). Counted from the KiCad layouts of 44 open source designs using the MQ-X.

What parts are used alongside the MQ-X?

The ATTINY404-SSNR, NMOS-DUAL, TPS613222A and LM393 appear in the most repositories here.

Which microcontrollers do boards using the MQ-X use?

Most are built on AVR/Arduino (26) and ESP32 (1).

How big is a typical board using the MQ-X?

The median is 22 × 54 mm, and 100% are two-layer designs.

What is the most popular open source board using the MQ-X?

By GitHub stars, Air quality sensor-MQ135-breakout hardware design by SolderedElectronics, with 7 stars.

Can I simulate one of these boards using the MQ-X before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part