15 open source boards using the PCA9685BS
Real designs built with the PCA9685BS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Open Shot Clock Display
DLaxV-Community-Projects-Hub
100 × 75 mm196 parts2LCERN-OHL-P-2.05ESP32
PCB-LEDs-Controller
MbFredys
134.4 × 106.7 mm36 parts2LCERN-OHL-W-2.05ESP32
PickleRick
icl-rocketry
100 × 37 mm196 parts6LMIT2STM32
NoNameComputer-2.0
PlanAndBuild
40 × 100 mm107 parts4LNo license2ESP32
NoU3
AlfredoSystems
46 × 56 mm113 parts4LNo license1MtN1 Draft 1
Momentum-Devices
40 × 46 mm64 parts4LCERN-OHL-W-2.01ESP32
Ricardo-Stark
icl-rocketry
117 × 49 mm298 parts6LNo license0Nixie clock
dalvador2
225.4 × 53.3 mm176 parts6LGPL-3.00ESP32
SmallKat CM4
keionbis
100 × 56 mm152 parts4LNo license0STM32
5-Channel-High-Current-Li po-Discharger
Lnotti
160 × 110 mm122 parts2LNo license0RP2040/RP2350
Titanrio
ggarciabaez
220.5 × 164.5 mm81 parts4LNo license0ESP8266
SEMG RECEIVER BOARD
Aaryaaaaaaa
142.8 × 72.3 mm22 parts2LNo license0ESP32
NoU3-Panelized
AlfredoSystems
138 × 168 mm113 parts4LNo license1MtN1 Draft 2
Momentum-Devices
40 × 46 mm50 parts4LCERN-OHL-W-2.01Nixie Control
dalvador2
21.2 × 35.6 mm26 parts6LGPL-3.00
How designs wire the PCA9685BS
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the PCA9685BS connects to, and the resistors, capacitors and other passives placed on it.
- The A3 pin is tied to GND on 11 of 12 designs.
- The SCL pin has a pull-up to 3.3V on 9 of 12 designs, most often 10 kΩ (then 2.2 kΩ).
- The SDA pin has a pull-up to 3.3V on 9 of 12 designs, most often 10 kΩ (then 2.2 kΩ).
- The A4 pin is tied to GND on 10 of 12 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A3pin 1 | Connected to: GND 92% | — |
| A4pin 2 | Connected to: GND 83% | — |
| VSSpin 11, 29 | Connected to: GND 86% | — |
| A5pin 21 | Connected to: GND 83% | — |
| SCLpin 23 | Connected to: The microcontroller 75%, a connector 42% |
|
| SDApin 24 | Connected to: The microcontroller 75%, a connector 42% |
|
| VDDpin 25 | Connected to: 3.3V 83% · a signal 17% |
|
| A2pin 28 | Connected to: GND 67% · a signal 17% | — |
20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Open Shot Clock Display by DLaxV-Community-Projects-Hub, PCB-LEDs-Controller by MbFredys, PickleRick by icl-rocketry and NoNameComputer-2.0 by PlanAndBuild.
The PCA9685BS in open source designs
The gallery holds 15 open source boards using the PCA9685BS from 12 GitHub repositories; a typical one measures about 100 × 56 mm and carries around 113 components.
73% use four copper layers or more, and 47% carry an open source license.
The most starred is Open Shot Clock Display by DLaxV-Community-Projects-Hub.
Parts used alongside the PCA9685BS
Microcontrollers on boards using the PCA9685BS
What boards using the PCA9685BS are built for
PCA9685BS: common questions
Where can I find a PCA9685BS reference design?
Each of the 15 boards on this page is a real design using the PCA9685BS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the PCA9685BS A3 pin connected?
The A3 pin is tied to GND on 11 of 12 designs. Counted from the KiCad layouts of 12 open source designs using the PCA9685BS.
What pull-up resistor is used on the PCA9685BS SCL pin?
The SCL pin has a pull-up to 3.3V on 9 of 12 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 12 open source designs using the PCA9685BS.
What pull-up resistor is used on the PCA9685BS SDA pin?
The SDA pin has a pull-up to 3.3V on 9 of 12 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 12 open source designs using the PCA9685BS.
What parts are used alongside the PCA9685BS?
The AMS1117-3.3, E220-400M22S, ESP32-S3, ESP32-S3FN8 and ESP32-WROOM-32 appear in the most repositories here.
Which microcontrollers do boards using the PCA9685BS use?
Most are built on ESP32 (7), STM32 (2), ESP8266 (1) and RP2040/RP2350 (1).
How big is a typical board using the PCA9685BS?
The median is 100 × 56 mm, and 27% are two-layer designs.
What is the most popular open source board using the PCA9685BS?
By GitHub stars, Open Shot Clock Display by DLaxV-Community-Projects-Hub, with 5 stars.
Can I simulate one of these boards using the PCA9685BS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.