6 open source boards using the SAA1099

Real designs built with the SAA1099, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the SAA1099

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SAA1099 connects to, and the resistors, capacitors and other passives placed on it.

  • The OUTL pin has a pull-up to 5V on 6 of 6 designs, most often 1.5 kΩ (then 1 kΩ).
  • The OUTL pin has a series resistor on 6 of 6 designs, most often 10 kΩ (then 1 kΩ).
  • The OUTR pin has a pull-up to 5V on 6 of 6 designs, most often 1.5 kΩ (then 1 kΩ).
  • The OUTR pin has a series resistor on 6 of 6 designs, most often 10 kΩ (then 1 kΩ).
OUTLpin 4Connected to: SAA1099 50%
  • Pull-up to 5V on 100% · 1.5 kΩ (3), 1 kΩ (3)
  • Series resistor on 100% · 10 kΩ (4), 1 kΩ (2)
  • Capacitor to GND on 83% · 1 nF (3), 10 nF (2)
OUTRpin 5Connected to: SAA1099 50%
  • Pull-up to 5V on 100% · 1.5 kΩ (3), 1 kΩ (3)
  • Series resistor on 100% · 10 kΩ (4), 1 kΩ (2)
  • Capacitor to GND on 83% · 1 nF (3), 10 nF (2)
IREFpin 6Connected to: Signal 100%
  • Pull-up to 5V on 100% · 10 kΩ (6)
DTACKpin 7Connected to: Not connected 50% · a signal 50%
  • Pull-up to 5V on 50% · 4.7 kΩ (3)
GNDpin 9Connected to: GND 100%
VCCpin 18Connected to: 5V 100%
  • Decoupling capacitor on 83% · 100 nF (5)

12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Snark barker by schlae, Zx multisound by UzixLS, Zx tsid by UzixLS and Zx sizif-512-ext by UzixLS.

The SAA1099 in open source designs

The gallery holds 6 open source boards using the SAA1099 from 6 GitHub repositories; a typical one measures about 191.5 × 71.3 mm and carries around 174 components.

83% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.

The most starred is Snark barker by schlae.

What boards using the SAA1099 are built for

SAA1099: common questions

Where can I find a SAA1099 reference design?

Each of the 6 boards on this page is a real design using the SAA1099. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the SAA1099 OUTL pin?

The OUTL pin has a pull-up to 5V on 6 of 6 designs, most often 1.5 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the SAA1099.

What pull-up resistor is used on the SAA1099 OUTR pin?

The OUTR pin has a pull-up to 5V on 6 of 6 designs, most often 1.5 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the SAA1099.

What pull-up resistor is used on the SAA1099 IREF pin?

The IREF pin has a pull-up to 5V on 6 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the SAA1099.

What parts are used alongside the SAA1099?

The YM3014B, 74LS08, 74LS125, 74LS138 and 74LS139 appear in the most repositories here.

How big is a typical board using the SAA1099?

The median is 191.5 × 71.3 mm, and 83% are two-layer designs.

What is the most popular open source board using the SAA1099?

By GitHub stars, Snark barker by schlae, with 687 stars.

Can I simulate one of these boards using the SAA1099 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part